manualshive.com logo in svg

AvL Technologies AAQ CIP, Setup & Operation Manual

Share
Download
AvL Technologies AAQ CIP Setup & Operation Manual Download Page 20

 

AAQ Controller Interface Panel (CIP)

 

 

 

 

 

19 

 

 

3.4.16.

 

Select Profile Screen 

 

Figure 27 - CIP Select Profile Screen 

The Select Profile Screen displays the list of profiles to choose from.  Whenever this screen is displayed, the asterisk 
will appear besides the currently active profile.  The up and down arrows will move the asterisk beside any desired 
profile.  When the Go button is pressed, the Profile Details screen will be shown for whichever profile is indicated by 
the asterisk.  To activate a new profile, first move the asterisk to besides its name with the up and down arrows.  
Once the desired new profile is indicated with the asterisk, while holding the stop key, press the go key and the 
selected profile will be activated.  To exit this screen without activating a new profile, press the stop button 3 times. 
To access the Profile Details Screen press the go button. 

√ 

3.4.17.

 

Profile Details Screen 

 

Figure 28 - CIP Profile Details Screen 

The Profile Details Screen displays the configuration settings for the selected profile.  The up and down arrows will 
scroll through the profile’s parameters.  To return to the Select Profile Screen, press either the stop or go button.  
(Note that upon return to the Select Profile Screen, the asterisk will appear besides the currently active profile, which 
may not be the profile whose details were just viewed.) 

XXXX↓ 

Summary of Contents for AAQ CIP










































Reviews:

No comments

Brands by name

Popular brands

Load more brands