Avital AviStart 3200 Installation Manual Download

Page: 32 / 42

system features learn routine

The System Features Learn Routine dictates how the unit operates. It is possible to access and change any of the

feature settings using the Valet/program switch. However, this process can be greatly simplified by using the

optional Personal Computer Interface or Bitwriter (

p/n 998T

). Any of the settings can be changed and then

assigned to one of up to four transmitters. This feature is called Owner Recognition. Each time that a particular

transmitter is used to disarm the system, the assigned feature settings will be recalled. Owner Recognition is only

possible when programming the unit via the computer interface or hand-held programmer.

If programming with the PC interface or the Bitwriter (

p/n 998T

), the learn routine can be locked or

unlocked. If the learn routine has previously been locked, it must be unlocked before proceeding with repro-

gramming the learn routine. This must be done by using either

p/n 998T

or the PC Interface module - this cannot

be done manually with the Valet switch. If the learn routine is locked, features cannot be changed.

The System Features Learn Routine dictates how the unit operates. Due to the number of features, the fea-

tures have been divided into two menus. It is possible to access and change any of the feature settings

using the Valet/Program switch. However, this process can be greatly simplified by using the optional DEI®

Bitwriter or 996T Personal Computer Interface. Any of the settings can be changed and then assigned to one of

up to four transmitters, a feature called Owner Recognition. Each time that particular transmitter is used to

disarm the system, the assigned feature settings will be recalled. Owner Recognition is only possible when pro-

gramming the unit via the 996T or the 998T DEI Bitwriter.

Using the optional DEI Bitwriter or PC Interface, the learn routine may be locked. Make sure the learn routine is

unlocked before programming features. If the horn generates one long honk when attempting to program the

unit, the learn routine is locked and must be unlocked using the DEI Bitwriter or PC before proceeding.

The programmable operating settings of this unit can be changed whenever necessary through the computer-

based Learn Routine. The Valet®/Program push-button switch, plugged into the blue port, is used together with

a programmed transmitter to change the settings. To program settings, remember: Key, Select Menu, Choose,

Transmit and Release.

To program the learn routine:

Key.

Turn the ignition on and then back off.

Select Menu.

Press and

HOLD

the Valet/Program switch until either the LED flashes once

and the horn honks once to select Menu One, or the LED flashes twice and the horn honks

twice to select Menu Two.

Summary of Contents for AviStart 3200











































Search results

Summary of Contents for AviStart 3200

Reviews:

Related manuals for AviStart 3200

Brands by name

Popular brands

Avital AviStart 3200, Installation Manual

Search results

Summary of Contents for AviStart 3200

Reviews:

Related manuals for AviStart 3200

Brands by name

Popular brands