Avital AviStart 3200 Installation Manual Download

Page: 28 / 42

programming jumpers

This jumper is used to determine the light flash output polarity. In the (+) position, the on-board relay is enabled

and the unit will output (+)12V on the WHITE wire, H1/2. In the (-) position, the on-board relay is disabled. The

WHITE wire, H1/2, will supply a 200mA (-) output suitable for driving factory parking light relays.

NOTE:

For parking light circuits that draw 10 amps or more, the jumper must be switched to a (-)

light flash output.

P/N 8617

or a standard automotive SPDT relay must be used on the H1/2 light

flash output harness wire.

In most cases, this jumper can be left in the OFF position. Some new vehicles use less than 12 volts in their

ignition systems. The unit may have trouble learning the tach signal in these vehicles. Changing the jumper to

the ON setting changes the trigger threshold of the digital tach circuit so it will work properly with these vehi-

cles. The vehicles affected include many newer Dodge/Chrysler/Plymouth vehicles, such as the Neon, Cirrus,

Stratus, Breeze and LH-based vehicles.

digital tach threshold on/off

light flash jumper

Summary of Contents for AviStart 3200











































Search results

Summary of Contents for AviStart 3200

Reviews:

Related manuals for AviStart 3200

Brands by name

Popular brands

Avital AviStart 3200, Installation Manual

Search results

Summary of Contents for AviStart 3200

Reviews:

Related manuals for AviStart 3200

Brands by name

Popular brands