Avital AviStart 3200 Installation Manual Download Page 2 | Manualshive

Page: 2 / 42

background image

2

© 2000 Directed Electronics, Inc. Vista, CA

table of contents

Bitwriter™, Stealth Coding Technology™, DEI®, Doubleguard®, ESP™, FailSafe®, Ghost
Switch™, Learn Routine™, Nite-Lite®, Nuisance Prevention Circuitry®, NPC®, Revenger®,
Silent Mode™, Soft Chirp®, Stinger®, Valet®, Vehicle Recovery System®, VRS®, and Warn
Away® are all Trademarks or Registered Trademarks of Directed Electronics, Inc.

Wiring Quick Reference Guide

. . . . . . . . . . . . 3

Warning! Safety First

. . . . . . . . . . . . . . . . . . 4

Installation Points to Remember

. . . . . . . . . . 5

Before Beginning Installation . . . . . . . . . . . 5
Finding the Tachometer Wire. . . . . . . . . . . . 5
Finding the Wait-To-Start Bulb Wire for Diesels. 6
After the Installation . . . . . . . . . . . . . . . . 6

Wiring Diagrams

. . . . . . . . . . . . . . . . . . . . . . 7

Primary Harness (H1) Wiring Diagram . . . . . . 7
Remote Start Ribbon Harness Wiring Diagram . . 7
Heavy Gauge Relay Satellite Wiring Diagram. . 8
Auxiliary Harness (H2) Wiring Diagram . . . . . 8
Remote Start Harness (H3) Wiring Diagram . . 8

Primary Harness (H1) Wire Connection Guide

. . 9

Relay Satellite Key Switch Interface Wire
Connection Guide

. . . . . . . . . . . . . . . . . . . . 12

Auxiliary Harness (H2) Wire Connection Guide

. 13

Remote Start Harness (H3)
Wire Connection Guide

. . . . . . . . . . . . . . . . 14

Neutral Safety Switch Interface

. . . . . . . . . . 16

Testing the Neutral Safety Switch . . . . . . . . 16

1995 and Newer Vehicle Anti-Theft
Systems (Immobilizers)

. . . . . . . . . . . . . . . . 18

Passlock I and Passlock II (PL-1 and PL-2). . 18
Passlock II (PK-3), Transponder-Based Systems . 19

Bypassing GM Vehicle Anti-Theft Systems

. . . . 19

Plug-in LED and Valet/Program Switch

. . . . . . 20

Programmer Interface, 3-Pin Port

. . . . . . . . . . . 21

Door Lock Harness (H4) Wire Connection Guide

. 21

Positive-Triggered, Relay Driven
Systems (Type A) . . . . . . . . . . . . . . . . . . 21

Negative-Triggered, Relay Driven
Systems (Type B) . . . . . . . . . . . . . . . . . . 22
Reversing Polarity System (Type C) . . . . . . . 23
Adding One or More After-Market
Actuators (Type D) . . . . . . . . . . . . . . . . . 24
Electrically Activated Vacuum (Type E) . . . . 25
One-Wire System, (Type F) . . . . . . . . . . . . 25
Type G: Positive (+) Multiplex . . . . . . . . . . 26
Type H: Negative (-) Multiplex . . . . . . . . . . 27

Programming Jumpers

. . . . . . . . . . . . . . . . . 28

Light Flash Jumper . . . . . . . . . . . . . . . . . 28
Digital Tach Threshold On/Off . . . . . . . . . . 28

Transmitter/Receiver Learn Routine

. . . . . . . . 29

Transmitter Configurations

. . . . . . . . . . . . . . 31

Standard Configuration. . . . . . . . . . . . . . . 31
Single Button Arm/Disarm Configuration . . . 31

System Features Learn Routine

. . . . . . . . . . . 32

Feature Menus

. . . . . . . . . . . . . . . . . . . . . . 34

Menu #1 . . . . . . . . . . . . . . . . . . . . . . . . 34
Menu #2 . . . . . . . . . . . . . . . . . . . . . . . . 34

Feature Descriptions

. . . . . . . . . . . . . . . . . . 35

Menu #1 . . . . . . . . . . . . . . . . . . . . . . . . 35
Menu #2 . . . . . . . . . . . . . . . . . . . . . . . . 36

Tach Learning

. . . . . . . . . . . . . . . . . . . . . . . 37

Shutdown Diagnostics

. . . . . . . . . . . . . . . . . 38

Rapid Resume Logic

. . . . . . . . . . . . . . . . . . 38

Timer Mode

. . . . . . . . . . . . . . . . . . . . . . . . 39

Valet Mode

. . . . . . . . . . . . . . . . . . . . . . . . . 40

Safety Check

. . . . . . . . . . . . . . . . . . . . . . . 40

Troubleshooting

. . . . . . . . . . . . . . . . . . . . . 41

The Bitwriter

®

(p/n 998T)

requires chip version 1.4 or
newer to program this unit.

«
1
2
3
4
...
»

Summary of Contents for AviStart 3200











































Reviews:

No comments

Related manuals for AviStart 3200

Brand: Viper Pages: 14

Brand: OBH Nordica Pages: 56

Brand: Trust Pages: 77

Brand: AVS Pages: 4

Brand: AVS Pages: 12

Brand: CrimeStopper Pages: 4

CS-9200 Samurai

Brand: CrimeStopper Pages: 3

Brand: Lanberg Pages: 12

WAKEBOX BT MT3148

Brand: media-tech Pages: 6

Brand: Satel Pages: 8

Brand: Pandora Pages: 35

Lalaloopsy Alarm Clock

Brand: Jazwares Pages: 11

Brand: Velleman Pages: 16

K9 SUPER MUNDIAL-SS

Brand: Omega Pages: 28

Brand: CrimeStopper Pages: 20

Brand: CrimeStopper Pages: 14

Brand: Philips Pages: 29

Brand: Philips Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands