Avidyne FlightMax EX500 Pilot'S Manual Download

Page: 166 / 184

Reference

Avidyne EX500/EX600 MFD

-154-

600-00078-001 Rev 05

11.14 Two-Way Datalink Messages

Table 11.15 Two-Way Datalink Messages

Two-Way Datalink

Messages & Colors

Meaning

Recommended

Pilot Action

Datalink Sensor is
Operating Normally

Satellite communicator
is operating normally
after a recoverable fault
was previously
acknowledged.

Acknowledge

Datalink Sensor is
NOT Communicating

Satellite communicator
has stopped
communicating.

Restart system. If
problem persists,
contact Avidyne.

Datalink Sensor
Configuration Error

COMM port is configured
incorrectly.

Restart system. If
problem persists,
contact Avidyne.

Datalink Sensor Data
is Invalid

EX500/EX600 receives
a “recoverable fault”
notification.

Have maintenance
check
configuration and
installation.

Narrowcast METAR
symbols > 90 minutes
(Orbcomm Only)

METARs are older than
90 minutes from their
time of reception.

Acknowledge

Narrowcast METAR
symbols > 75 minutes
(Iridium Only)

METARs are older than
75 minutes from their
time of reception.

Acknowledge

Narrowcast AIRMETs/
SIGMETs > 90
minutes

AIRMETs/ SIGMETs are
older than 90 minutes.

Acknowledge

Narrowcast TFRs > 90
minutes

TFR data are older than
90 minutes.

Acknowledge

Narrowcast TAFs > 90
minutes

TAF data are older than
90 minutes.

Acknowledge

Narrowcast Lightning
> 20 minutes

Lightning information is
older than 20 minutes.

Acknowledge

Narrowcast Data not
yet received

Datalink is Enabled and
no Datalink data has
been received within 10
minutes of EX500/
EX600 initialization
complete.

Acknowledge

Summary of Contents for FlightMax EX500

























































































































































































Search results

Summary of Contents for FlightMax EX500

Reviews:

Related manuals for FlightMax EX500

Brands by name

Popular brands

Avidyne FlightMax EX500, Pilot'S Manual

Search results

Summary of Contents for FlightMax EX500

Reviews:

Related manuals for FlightMax EX500

Brands by name

Popular brands