manualshive.com logo in svg

Avidyne 700-00004 Series, Installation Manual, Page: 54 / 132

Share
Download
Avidyne 700-00004 Series Installation Manual Download Page 54

 

EX5000 Installation Manual

 

 

P/N 600-00073 Rev 24

- 44 -

Note:

The antenna position setting and stabilization source must agree with the WX-500 jumper 
setting and the physical mounting location of the antenna.

4.

For the TWX-670 the following options are available in the TWX-670 Config page:

■

Enable geo stabilization – an external position source (GPS or FMS) connected to the sensor 
will stabilize the lightning strikes to the aircraft position

■

Enable heading stabilization – an external heading source (e.g., a synchro) connected to the 
sensor will stabilize the lightning strikes to the aircraft heading.

■

Enable Audio Output – if connected to the aircraft audio panel, the TWX-670 will provide 
audible warnings concerning nearby lightning strikes.

These options are only available after the Sensor and Port options have been selected and 
the MFD restarted.  Green check marks will appear next to each option if the TWX-670 agrees 
with the configuration.  If red X’s appear, it may be because another display connected to the 
sensor is trying to set a different configuration.  Consult the TWX-670 installation manual for 
more information.

5.

When you are done, press Save.  Press Cancel to exit without saving changes.

6.

Changes do not take effect until the MFD has been restarted.  From the Maintenance Mode Page, 
press Restart System.

In addition to the settings on the Lightning Setup Page, the following buttons may be available:

●

WX-500/TWX-670 Diags

 – allows access to the lightning sensor diagnostic modes.  See your 

sensor’s Installation Manual about how to verify software versions, wiring configurations, antenna 
environment, and fault logs (not available on all software releases).

●

Self Test (WX-500)

 – Runs the WX-500 Self Test and reports Pass or Fail.  See the WX-500 

Installation Manual for information about testing and the interpretation of the results (not available 
on all software releases).

5.6.2 Lightning Sensor Checkout 

After the MFD has been restarted, any of the following messages may appear in the main viewing 
screen or the message bar and Setup page.

Table 19:  Lightning Sensor Messages 

Message

Meaning

Lightning Sensor is Operating Normally

Verifies that strike data to the MFD is valid.

Lightning Sensor in Demo Mode

Demo mode has been selected as the operating mode from the 
Lightning Setup Page.

Lightning Sensor is in Noise-Monitor Mode

Noise-Monitor mode has been selected as the operating mode from 
the Lightning Setup Page.

Lightning Sensor in Test Mode

Test mode has been selected as the operating mode from the 
Lightning Setup Page.

Lightning Sensor ERROR

The sensor system has reported an error that may mean current 
data is incomplete or erroneous. The error may clear.

Lightning Sensor has FAILED

The sensor system has reported an error that may mean current 
data is incomplete or erroneous. The error will not clear until power 
is removed from and reapplied to the sensor system. 

Summary of Contents for 700-00004 Series





































































































































Reviews:

No comments