Avia D 100 User Manual Download Page 65

Page: 65 / 108

O P E R A T I N G I N S T R U C T I O N S

Secure the trailer rear wheels with

chocks.

The front trailer axle must remain ste-

ering.

Adjust the trailer draw bar into a

height of the trailer hitch.

When engaging the reverse speed,

make sure that nobody is standing
between the trailer and vehicle.

Make sure that the trailer is coupled

correctly.

Attach the brake hoses coupling he-

ads and plug connectors of electric con-
ductors.

Check the brake system and lights

for a correct function.

Proceed very carefully when towing

a trailer and do not exceed the allo-
wable load limits.

When stopping during uphill or down-

hill driving, check the manual brake for
a good efficiency. It must hold the whole
vehicle combination in a gradient on
the spot.

Basic rules for the trailer coupling

Warning!

The pieces of information men-
tioned in this chapter are the basic
ones only. You should abide mainly
by the instructions given in the Op-
eration Manual for the connected
vehicle.

Summary of Contents for D 100













































































































Search results

Summary of Contents for D 100

Reviews:

Related manuals for D 100

Brands by name

Popular brands

Avia D 100, User Manual

Search results

Summary of Contents for D 100

Reviews:

Related manuals for D 100

Brands by name

Popular brands