![background image](http://html1.mh-extra.com/html/avery-dennison/st9500/st9500_operators-and-service-manual_3030470015.webp)
15
0.55s, 0.60s, 0.25, 0.28 …” and it will then repeat.
Button “2” (“INTERVAL”): This is to change the interval. With each press the display
will change to the next value of “…, 0s, 0.1s, 0.2s, 0.3s, 0.4s, 0.5s, 0.6s, 0.7s, 0.8s, 0.9s,
1.0s, 0s…” which forms a loop.
Button “3” (“MODE”): This is to change the Cycle Mode. With each press the display
will change to the next value of “…, C_, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, C_, 1, 2 …” which
forms a loop.
Button “4” (“COUNT/RESET”): This is to switch the display between the
aforementioned two different counters and to reset the counter that can be reset.
With each “short press” (keep pressing the button less than 2 seconds) the display
will switch between “CTR” and “LIFE”.
With each “long press” (keep pressing the button longer than 2 seconds) the counter
that can be reset will be reset
Button “5” (“SAVE”):
With each “short press” to save the settings you just made to the RAM in the
machine, so that this setting can be activated when you power on the machine next
time.
With each “long press”, the panel will display a password entering dialogue and you
can switch the machine between Password Enable and Disable modes.
4. Password Enable and Disable Functions:
To use the password Enable and Disable function is for better management of the privileges
in changing machine parameters. The machine reserves the availability to switch from Password
Enabled Mode to Password Disabled Mode and vice versa. In the former mode, the user need to
enter a valid password before he can change the motor parameters, then need press the button
“5” (SAVE) to save it after changing the motor parameters; while in the latter mode, the user can
change the parameters without any password and it can save the parameters real time.
The machine will be set to Password Disabled Mode when it is shipped from the factory.
4.1 Switch between Password Enabled Status and Password Disabled Status:
a). Long press (keep pressing over 2 seconds) the Button “5” at any time when the machine is
powered on, and the display will show a indication as “XXX” for the user to enter a password.
After a valid password, the machine will be switched from Password Disabled Status to
Password Enabled Status or reverse.
b). When you want to enter a password, you will use the buttons described as below:
Press “1” to change the display of the first digit of the three. With each press the first
digit will change to the next value of “…0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, 1…” and then it
repeats.
Press “2” to change the display of the second digit and pressing “3” to changes the
display of the third digit.
Press “5” as confirmation key to confirm the password you just enter.
If the password is invalid, the display will show “XXX” again; Then please try to
enter a valid password by the abovementioned procedure;
If the password is valid, the display will show “Enable” or “Disable”; then press “1”
button to switch between the two, and then press “5” to confirm.
Summary of Contents for ST9500
