Avery Dennison 1050 - Puma User Manual Download Page 2

Page: 2 / 40

User Manual

TTX 450/650/950/1050 – Puma/Lion/Tiger/Tiger XXL – TDI/STDI/XXtreme –

S45/65/95/105

05/08 Rev.

2.14

CONTENTS

General ................................................................................................................................. 4

Copyright ..........................................................................................................................................4

IMPORTANT OPERATING INSTRUCTIONS..................................................................................4

Initiation ................................................................................................................................ 5

Unpacking of Printer.........................................................................................................................5

Set - Up and Connection of Printer .................................................................................................6

Connections TTX: ..................................................................................................................... 6

Connections -TDI: ..................................................................................................................... 6

Connection of External Units............................................................................................................7

Card Plug in Modules .......................................................................................................................7

SLOTS TTX............................................................................................................................... 7

SLOTS TDI................................................................................................................................ 8

Card hardware..................................................................................................................................8

PCMCIA card pin assignment ................................................................................................... 9

Memory types............................................................................................................................ 9

PROM card (Programmable Read Only Memory)....................................................................... 9

EPROM card (Erasable Programmable Read Only Memory)..................................................... 9

EEPROM or E²PROM (Electric Erasable Programmable Read Only Memory).......................... 9

FLASH RAM / PROM card ........................................................................................................ 10

RAM card (Random Access Memory)....................................................................................... 10

Card use .........................................................................................................................................10

Card type ........................................................................................................................................10

Set up mode ....................................................................................................................... 11

Winding Diagrams ..........................................................................................................................11

TTX x50 / Wildcats .................................................................................................................. 11

TDI / XXtreme ......................................................................................................................... 11

Insertion of Document Material ......................................................................................................13

Material exchange ..........................................................................................................................15

Insertion of fan folded material.......................................................................................................15

Insertion of Thermal Transfer Ribbon ............................................................................................15

Adjustment of ribbon unwind rewind tension..................................................................................17

Positioning of gap sensor ...............................................................................................................18

Adjust position of printhead ............................................................................................................19

Adjust pressure of printhead ..........................................................................................................19

Adjustment to thickness of material ...............................................................................................20

Installation of option .......................................................................................................................21

Short Tag Option ................................................................................................................ 22

Fonts...............................................................................................................................................22

Modes of operation - operation........................................................................................... 23

New Start of Printer .......................................................................................................................23

Restart of Printer ............................................................................................................................23

Call of Program Version .................................................................................................................23

Modes of operation - OFFLINE ......................................................................................................23

Modes of operation - OFFLINE ......................................................................................................24

Modes of operation - ONLINE ........................................................................................................25

Summary of Contents for 1050 - Puma









































Search results

Summary of Contents for 1050 - Puma

Reviews:

Related manuals for 1050 - Puma

Brands by name

Popular brands

Avery Dennison 1050 - Puma, User Manual

Search results

Summary of Contents for 1050 - Puma

Reviews:

Related manuals for 1050 - Puma

Brands by name

Popular brands