background image

17

S w i v e l   H e a d   S e r v i c i n g   I n s t r u c t i o n s

A c c e s s o r i e s

5

7

17

18

19

20

Swivel heads should be serviced at weekly intervals.

Remove the complete head using the reverse procedure to
the ‘Fitting instructions’ omitting step ‘

L

’.

If Guard 

1

is at all damaged it must be replaced by a new

one.

Any worn or damaged parts should be replaced.

Pay particular attention to jaw carrier items in the upper
illustration opposite as follows:
Check wear on Jaws 

17

.

Check that Jaw Spreader Tube 

18

is not distorted.

Check that Spring 

19

is neither broken or distorted.

Check that Spring Guide 

20

is not damaged.

Check that spring clip 

7

is not distorted. When removing

Spring Clip 

7

, use two screwdrivers as shown in the lower

illustration opposite.

Check for excessive wear on slots of Body 

5

.

Assemble according to fitting instructions.

Item numbers in bold refer to Swivel Head illustrations on
this page. Guard 

1

refers to illustration on page 16.

While nose tips and jaws will vary for each swivel head, other components remain constant within each type of head. See table below
For nose tips and jaws part numbers see within the table on pages 9 to 12.

C O N S T A N T C O M P O N E N T S

ITEM

DESCRIPTION

STRAIGHT SWIVEL

RIGHT-ANGLE SWIVEL

1
2
3
4
5
6
7
8
9

10
11
12
13
15
16
18
19
20
21
22
23

GUARD
CIRCLIP
JAW CARRIER
LEVER
BODY
PIVOT PIN
SPRING CLIP
ROLLER
ADAPTOR
LOCKING RING
SPINDLE 
DOWEL PIN
SCREW
PIVOT PIN
SCREW
JAW SPREADER
SPRING
SPRING GUIDE
SCREW
PLATFORM
SCREW

07494-05000

-

07494-03026

-

07494-03015
07343-02207
07495-03900
07007-00039
07345-03001
07345-03003
07345-03002
07007-00038
07342-02207

-

07494-03028
07346-03101
07165-00305
07494-03027
07001-00368
07345-00401

-

07495-03003
07004-00105
07494-03026
07495-03004
07495-03002
07343-02207
07495-03900
07007-00039
07345-03001
07345-03003
07345-03002
07007-00038
07342-02207
07343-02207
07494-03028
07346-03101
07165-00305
07494-03027


07210-00804

Summary of Contents for Genesis nG3

































Reviews: