AVANT A424013 Operator'S Manual For Attachment Download Page 30 | Manualshive

Page: 30 / 36

background image

30 (36)

To ensure the stability of an uncoupled attachment, place it on a pallet as shown in the figure below:

DANGER

Risk of crushing -
Uncoupled bucket may
tip over.

Ensure stability

of uncoupled
attachment. Keep a safe
distance during coupling.
Ensure the stability by
placing the attachment
firmly on the ground to a
stable position with its
long side against the
ground or securing it
otherwise.

WARNING

Risk of tipping over of an uncoupled attachment - Use tie-down equipment if
necessary.

Empty the bucket before storage. Store the attachment only on level surface.

Secure the attachment during storage e.g. by using load straps.

«
...
28
29
30
31
32
...
»

Summary of Contents for A424013





































Reviews:

No comments

Related manuals for A424013

Aqua Dual Mate ADM Series

Brand: ChemChek Pages: 2

Brand: BENKISER Pages: 13

Brand: Delta Clean Pages: 2

ARCTIC Compact 12L

Brand: Ugolini Pages: 28

ARCTIC Compact Series

Brand: Ugolini Pages: 40

AccuDose 38741GB

Brand: Hydro Pages: 4

Brand: CASO DESIGN Pages: 83

Brand: Manitowoc Pages: 52

Brand: Knight Pages: 20

UniTech Warewash

Brand: Knight Pages: 24

Brand: Evo-water Pages: 13

soft duomatik 2

Brand: Evo-water Pages: 15

Brand: Kimberly-Clark PROFESSIONAL Pages: 33

Brand: Modena Pages: 23

Brand: Metasys Pages: 18

Brand: Aqualife Pages: 24

Brand: ICO Pages: 40

Brand: PacDent Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands