background image

AS-6105 SH 

Installation Guide

 P.11

The Module can only be programmed Function by Function

. After selecting a Mode 

(from 1 to 3), you will be taken to the first Function of that Mode. After entering an Option 
number for Function 1, you will be automatically taken to Function 2, and so on; therefore, be  
ready to re-enter all option numbers for all functions of the Mode you are accessing. 

You 

may not skip Functions.  

For each Function, select one of the four Options by pressing the corresponding 
button on the Transmitter: 

x

LOCK

 

  for 

Option 

1, 

x

UNLOCK

   for Option 

2, 

x

TRUNK

   for 

Option 

3, 

or 

x

START

  

 

for 

Option 4. 

Table 3 

Once an Option has been selected the Parking Lights will flash 1, 2, 3 or 4 times depending 
on the selected Option. At any time, you can press the Brake Pedal to return to the 
Programming Centre (Programming Modes and Tach Programming). 

Options Programming  

Mode 1

*indicates default setting 

Function 1 – Ignition-Controlled Door locks 

OPTION 1* 

Ignition Lock 

DISABLED

OPTION 2 

Ignition Lock 

ENABLED

OPTION 3 

Ignition 

UNLOCK 

ONLY

OPTION 4 

Ignition 

LOCK

 ONLY 

Function 2 – Secure Lock  

OPTION 1* 

Secure Lock disabled (1-sec. Disarm pulse.) 

OPTION 2 

Secure Lock enabled in Smart Mode. 

OPTION 3 

Secure Lock disabled (0.5 Sec Disarm pulse) 

OPTION 4 

Secure Lock enabled in Normal Mode. 

Function 3 – Door Locks Pulse Timing 

OPTION 1* 

7/10 Second Lock/Unlock pulses. 

OPTION 2 

4 Seconds Lock/Unlock pulses. 

OPTION 3 

7/10 Seconds Lock pulse and two 1/4 second unlock pulses. 

OPTION 4 

1/10 Second Lock/Unlock pulses. 

Function 4 – AUX 3 Programming 

OPTION 1* 

Constant while the 

TRUNK

 button is pressed  

OPTION 2 

1-sec. Trunk 1 output when 

TRUNK

button pressed for 3 sec. while Ignition is 

OFF

and Data output. 

OPTION 3 

TRUNK

 with Disarm/Rearm (Shock is ignored while Zone 3 is opened.) 

OPTION 4 

TRUNK 

1 sec output 

ON/OFF

Function 5 – AUX 2 Programming 

OPTION 1* 

Priority Door access (Pressing 

UNLOCK

 a 2

nd

 time triggers 

AUX 2

)

 

 

Car Finder enabled (pressing

LOCK 

and 

UNLOCK 

triggers Car Finder) 

The Driver’s Door unlocks upon the 1st pressing of the 

UNLOCK

 button; 

 

 

All Doors unlock on any subsequent pressing of the 

UNLOCK

 button. 

OPTION 2 

Toggle 

ON/OFF

 with a 30-second timeout (press 

LOCK 

and 

UNLOCK

)

Car Finder disabled.  

OPTION 3 

Constant output while pressed (press 

LOCK 

and

UNLOCK

)

Car Finder disabled.  

 

OPTION 4 

Priority Door access on 2

nd

 Unlock, and Car Finder enabled. 

x

The Driver’s door unlocks upon the 1

st

, 3

rd

, 5

th

 … pressing of the 

UNLOCK

 button. 

Summary of Contents for AS-6105 SH





















Reviews: