background image

P.12

 Installation 

Guide

AS-6105 SH 

x

All Doors unlock upon the 2

nd

 , 4

th

, 6

th

 … pressing of the 

UNLOCK

button. 

Mode 2 

 

*indicates default setting

Function 1 – Home Valet Mode 

OPTION 1 

Home Valet enabled 

OPTION 2* 

Home Valet disabled 

OPTION 3 

Home Valet disabled 

Function 2 – Safe Start 

OPTION 1 

Safe Start enabled 

OPTION 2* 

Safe Start disabled 

OPTION 3 

Swap Start

 – increased safety mode: 

x

To Start: press Lock and Unlock buttons simultaneously

.

x

Press the

START 

button to activate

AUX 2

.

Function 3 – Engine Run Time 

OPTION 1 

Run time - 4 minute in Gas mode / 9 minutes Diesel mode. 

OPTION 2* 

Run time - 15 minute in Gas mode / 20 minutes

 Diesel mode. 

OPTION 3 

Run time - 25 minute in Gas mode / 30 minutes Diesel mode. 

Function 4 – Idle/Turbo Mode 

OPTION 1 

Idle/Turbo Mode disabled 

OPTION 2* 

Turbo Mode enabled 

OPTION 3 

Turbo Mode disabled 

Function 5 – Engine Type and Cold Weather Mode 

OPTION 1 

Diesel Engine Mode and 20-minute run time in Cold Weather Mode.

OPTION 2* 

Gasoline Engine Mode and 4-minute run time in Cold Weather Mode.

OPTION 3 

Diesel Engine Mode and 9-minute run time in Cold Weather Mode.

Mode 3 

 

*indicates default setting

Function 1 – Siren Chirps  

OPTION 1 

Warning Chirps only; Lock Confirmation if the Lock button is press 2nd time. 

OPTION 2* 

Chirps enabled. 

OPTION 3 

Chirps enabled with Open-Zone notification. 
(Siren warning 10 sec. after arming if a door is left open) 
(Also used for vehicles with Dome Light Delay). 

OPTION 4 

Chirps disabled and Lock confirmation if the 

LOCK

 button is press 2nd time. 

Function 2 – Passive Or Active Arming 

OPTION 1 

Active Arming 

OPTION 2* 

Passive Arming (30 sec.) 

OPTION 3 

Passive Arming (30 sec.) / no 

TWO-STAGE DISARM

OPTION 4 

Active Arming with Disarmed Notification. 

Function 3 – Ignition Monitoring: Siren Mode / Horn Mode 

OPTION 1 

Siren Mode: Ignition Monitoring – disabled. 

OPTION 2* 

Siren Mode: Ignition Monitoring – enabled. 

OPTION 3 

Horn Mode: Ignition Monitoring – disabled. 

OPTION 4 

Horn Mode: Ignition Monitoring – enabled. 

Function 4 – Shock Sense / Warn Away 

OPTION 1 

Shock Sense - Ignored / Warn Away – ignored 

OPTION 2* 

Shock Sense - monitored / Warn Away – monitored 

OPTION 3 

Shock Sense - Monitored / Warn Away – ignored 

OPTION 4 

Shock Sense - Ignored / Warn Away – monitored 

Function 5 – Ignition Valet 

OPTION 1 

Ignition Valet - DISABLED 

Summary of Contents for AS-6105 SH





















Reviews: