Jun/22/2009
RST1000 OP REV.A
13
long as you wish. To exit passive by-pass, press the transmitter
or
button and the system will return to
normal status.
G. ACTIVE DISARMING – UNLOCK & DISARM:
1. Press
button on the transmitter.
2. The siren will chirp twice and parking light flash twice to indicating that the security system is now
disarmed. The vehicle’s door will unlock and dome light turns on for 30 seconds upon disarming when
interfaced with the security system.
SILENT DISARMING:
Spin up the
switch to the page
1
and
then press the “Silent Disarm” button or press the transmitter
and
buttons at the same time to disarm your security
system, No chirp sound will be heard, arm and disarm
confirmation will be through the vehicles parking lights only.
TAMPER DISARMING: If alarm triggered, upon disarming the system, the siren will chirp 4 times and the
parking light will flash 3 times.
PATHWAY ILLUMINATION: This feature turns the parking lights “ON” for 30 seconds upon an unlock
signal and for 10 seconds upon the lock signal. (Programming required)
TWO STEPS DOOR UNLOCK: This feature will independently unlock the driver’s door only when
disarming the security system. Pushing the
button a second time within 3 seconds will unlock the
other doors. (Additional installation is required)
AUTOMATIC RE-ARM: If this feature is selected, the security system will automatically re-arm itself in 60
seconds after disarming with remote transmitter. Automatic rearm will cancel if the ignition is turned ON
and will pause if any door is opened before the 60 seconds timer has elapsed.
H. DISARMING WITHOUT A TRANSMITTER
OVERRIDES THE ALARM WITHOUT PASSWORD PIN CODE: (Factory Default Setting)
The Override function may be used if the remote transmitter is lost or inoperative.
1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound.)
2. Within 10 seconds push and release the valet switch
The alarm will stop sounding and enter the disarmed mode. You can now start and operate the vehicle
normally.
OVERRIDE THE ALARM WITH PASSWORD PIN CODE:
If the valet switch is located in a place that can be easily found, this security system allows the consumer to
program a password pin code offering a higher level of security.
1. Enter the vehicle and turn the ignition switch to the 'ON’ position. (Alarm will sound.)
2. Within 5 seconds, enter your chosen the first digit code by pressing and releasing the Valet Switch.
(When you are finished with the above procedures, the system's siren stops alarming and the parking
lights stop flashing, but the vehicle cannot be started and driven away.)
3. If you use one digit to be a password pin code, skip to Step 6. If you use two digits to be a password pin
code, advance to Step 4.
4. Within 15 seconds of the last digit code enter (the 1st code), turn the Ignition Switch “Off” and then “On”.
5. Within 15 seconds, enter your chosen of the second digit code by press and release the Valet Switch.
6. Turn the ignition switch to the “OFF” position. [4] Chirps form siren/horn, [3] flash from parking light to
indicate the system was disarmed.
Note: If someone keys-in the wrong password pin code, the system allows him to make 2 mistakes. If the
third code is still wrong, it will automatically shut down for 5 minutes. During this period the system
will not accept any code and the LED will “pause on” (the LED will turn on 1 second
and turn off 0.1 second).
EXAMPLE: To Override The System With The Password Code 83, you would;
1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound.)
2. Within 5 seconds, Press and Release the Valet Switch 8 times
(When finish the above procedure, the system's siren will stop alarming and the parking lights will stop
flashing, but the vehicle cannot be started and driven away.)
3. Within 15 seconds of the last digit code enter (the 1
st
code), turn the Ignition Switch “Off” and then “ON”.
4. Within 15 seconds, Press and Release the Valet Switch 3 times
