Automatic Technology Dominator Syncro ATS-3AM Instruction Manual Download Page 2 | Manualshive

Page: 2 / 28

background image

WARNING!:

It is vital for the safety of persons to follow all

instructions. Failure to comply with the installation instructions
and the safety warnings may result in serious personal injury
and/or property and remote control opener damage. Please
save these instructions for future reference.

ELECTROCUTION!

: To reduce the risk of electric shock, this

equipment has a grounding type plug that has a third (grounding)
pin. This plug will only fit into a grounding type outlet. If the
plug does not fit into the outlet, contact a qualified electrician
to install the proper outlet. Do not change the plug in any way.
This operator is not equipped for permanent wiring. Contact a
qualified electrician to install a suitable receptacle if one is not
available.

«
1
2
3
4
...
»

Summary of Contents for Dominator Syncro ATS-3AM





























Reviews:

No comments

Related manuals for Dominator Syncro ATS-3AM

Brand: CAME Pages: 40

Brand: Xcel-Arc Pages: 20

RCT-224 Trailer

Brand: Miller Electric Pages: 24

Brand: Beninca Pages: 24

Fantech SE 704N

Brand: SystemAir Pages: 20

Brand: Kompernass Pages: 66

Brand: Zhermack Pages: 296

Brand: Electrex Pages: 36

Brand: Command access Pages: 6

RADIANT PANEL SYSTEM

Brand: Roth Pages: 8

Brand: SUGATSUNE Pages: 12

Brand: Yale Pages: 6

Tri-Pack 50 Series

Brand: Yale Pages: 6

Brand: Stel Pages: 38

Brand: H&S AUTOSHOT Pages: 25

Fireguard 2900 Series

Brand: Sargent Pages: 6

Brand: SEA Pages: 6

Brand: FlexiForce Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands