Diamond PD
Power Drive
: Instruction Manual
Dominator Tempo & Syncro Instruction Manual
ATS-3AM & ATS-2AM
13
© Copyright 2019
6.4 Setting Speed and Limits
Fig.6.4.1
6.4.1 Set the Limit Positions and adjust drive speed:
The Limit Positions can vary due to site conditions, such as uneven
ground. When setting the Close limit, ensure the position is when the
door makes first contact with the ground. Alternatively for the Open
limit the position should be at the height of the garage opening.
NOTE: The drive speed is set to the fastest setting by default. This may
not be suitable for larger doors or for single piece doors. For tilt doors
(J-Type only), please refer to Appendix G for initial setup.
a. Switch power on and the BLUE LED on the CLOSE button
will start to flash and the GEAR
LED is lit to indicate that the
opener is ready to set the Close travel limit
(Fig 6.4.1)
.
b. Press either the CLOSE
or OPEN button to move the door to
the halfway point.
WARNING! In setting the close limit position, do not
force the door into the floor with excessive force, as
this can interfere with the ease of operation of the
manual release mechanism.
Door Opener
Speed Mode
STATUS
MAIN LIGHT
Fast (Default)
On
3 Flash
Medium
On
2 Flashes
Slow
On
1 Flashes
WARNING! The door will automatically close, open and
close again after the next step. Ensure that nothing is in
the door’s path.
NOTE: If unhappy with the speed or travel limit setting, restart this
procedure by resetting the door limit positions as per below first.
6.4.2 Clearing the Door Limit Positions
Limit positions can be deleted by:
a. Press the MODE button repetitively until the GEAR
LED is lit.
b. Press and hold the MODE button for 10 secs, let the MODE button
go when the main light stops flashing.
c. The close LED will flash continuously to indicate limits have been
cleared.
NOTE: If no action is taken within 30 seconds, the opener will return to
normal operating mode and restore the original settings.
d. Follow from CLOSE limit: above to set new limit positions.
CLOSE limit:
(i) Press and hold the CLOSE button
to start closing the door,
taking note of the speed the door moves.
(ii) If the close speed is not suitable, to make a change, press
and hold the CLOSE button and by pressing the
STOP / SET button on the opener it will cycle through all
three speed modes as shown in table.
(iii) Once at the desired speed, release the CLOSE button.
(iv) To set the close limit, inch the door by making single presses
of the CLOSE button
to the desired position. We
recommend the CLOSE limit position being the first point of
contact of the rubber strip ( at the bottom of the door) with
the ground.
(v) If the door overshoots, press the OPEN button
to move
the door in the OPEN direction.
(vi) When the door is at the desired CLOSE position, press the
STOP / SET button on the opener, the GREEN LED on the
OPEN button
will now flash.
OPEN limit:
(i) Press and hold the OPEN button
to start opening the door,
taking note of the speed the door moves.
(ii) If the open speed is not suitable, to make a change, press
and hold the OPEN button and by pressing the
STOP / SET button on the opener it will cycle through all
three speed modes as shown in table.
(iii) Once at the desired speed, release the OPEN button.
(iv) Continue inching the door to the desired position.
(v) To set the open limit, inch the door by making single presses
of the OPEN button
to the desired position. We
recommend the OPEN limit position being the height of the
garage opening.
(vi) If the door overshoots, press the CLOSE button
to move
the door in the CLOSE direction.
(vii) When the door is at the desired OPEN position, press the
STOP / SET button The door will now automatically close and
open to calculate the safety obstruction settings.
6.4.3 Re-profiling the Door
Re-profiling is a simplified way of re-learning the travel characteristic
of a previously setup Limit Switch travel installation. Re-profiling can
be used when the travel characteristics of the door change due to
mechanical adjustments etc. To initiate a re-profile:
a. Limits must be set.
b. Press the MODE button repetitively until the GEAR
LED is lit.
c. Press and hold the CLOSE button
for two seconds, the door
will open and close by itself to record profile.
Refer to Appendix B & C for adjustments to
margins.
tip
