4
installation
5.
Product Spacers, 4-Selection Shelf.
A product spacer is
used to reduce the width of the product area and should
be used on any 4-selection snack shelf where the product
width is 4-1/2” or less. Spacers should fit within 1/8” of the
product but should not fit tight against the product. There
are three positions in each snack space where these
spacers can be placed. To install the spacer, align the lock
ears (on the lower edge of the spacer) with one of the
three sets of slots (one front and one rear).
(Figure 4.)
Push the spacer to the rear to allow the ears to enter
the slots, then allow the spacer to move forward. Be sure
the ears are in the same set of slots, front and rear.
(Figure 4.)
C o n t i nue loading all spira
l s. Adjust with
spacers where needed in the top shelf. Return the top
shelf to the vend position and following this procedure,
load the remainder of the large spiral shelves. The shelf
divider separating the right (lock side) column from the
next column is movable to allow vending of products wider
than 5-1/2” in the second column. If this is used, the right
column must be used to vend narrower products.
6.
Loading Main Product Candy Shelves.
The 8-selection
(candy type) shelves are loaded similar to the 4-selection
s h e l ve s, except that, the bottom of the product sits on the
shelf in front of the spiral wire
(Figure 5.)
that rests on the
s h e l f. These products must also fit properly in the spiral
s p a c e.
Do not fo rce product into spiral.
These spirals are
r e m oved and installed the same as the large spiral
( F i g u r e
3 . )
, except that, the front end position is different
( a p p r oximately 5 o'clock)
(Figure 5.)
and the front left side
of the spiral must be behind the small tab located on the left
side of the product space side wa l l .
(Figure 5., Detail A)
7.
Product Spacers, 8-selection shelf.
The 8-selection
shelves are equipped with a product spacer (Figure 6.)
that can be pivoted from the right side of each product
space. These spacers should be pivoted out to hold the
product upright, but not tight against the product. Leave
about 1/8" clearance between the spacer and the product.
8.
Product Pusher.
The machine contains enough pushers
for you to install a pusher on each candy spiral.This plastic
part is designed to push the top of the product forward
while it is vending, helping it to fall from the shelf. It can also
be used with products that have the wrapper end flap on
the outside of the package. In this case, the pusher
prevents these products from hanging on the spiral by
spreading the flap. The pusher is installed approximately
210 degrees from the front end of the spiral with the tab
extending forward.
(Figure 7.)
Locate the pusher in its
proper position, hold it against the spiral wire and push the
semi-circular part around the spiral wire.
Note: Not every selection spiral will need a product
pusher. (Example: box items)
Figure 5.
Placement of product on main product candy
shelves and front end of spiral.
Figure 6. 8-selection shelf product spacer positioned to hold
candy upright.
Summary of Contents for SNACKSHOP LCM5 Series
