Automatic Products SNACKSHOP LCM5 Series, Instruction Manual

Page: 6 / 60

2
unpacking
The Snackshop LCM is assembled and packed so that a min-
imum amount of time is necessary for preparation to install it
on location. The following steps are recommended to insure
correct unpacking.
1. Shipping Damage. Thoroughly inspect the exterior of the
carton for damage which may have occurred during ship-
ment. Report any damage to delivering carrier and follow
their instructions.
2. Remove staples from lower edge and those at top of car-
ton, and slit carton vertically at the taped corner. Open and
remove carton. Remove the remainder of the packing
material. Machines shipped with a lock in place, the keys
are located in the coin return cup.
3. Removing Vendor with a Fork Lift Truck . Remove the
carton from the vendor. Open the door on the vendor and
remove the hold down bracket at the front center of the
cabinet base and close the vendor door. From the front of
the vendor, tip the vendor backward and run forks under
the cabinet.
4. On machines with lock in place, unlock, and turn handle to
open door. When no lock is furnished, remove tape and
turn handle. Swing door to its full open position.
5. Remove all packing tape and paper from various areas of
machine and the shipping strap.
6. Warranty . The warranty card is attached to the cover of this
manual. It must be filled out in full and mailed at once to
insure coverage.
installation
1. Leveling the Machine on location is important for the
proper function of the machine. The four leveling screws in
the legs are the means of leveling the machine. After posi-
tioning the machine, level machine in front to rear and right
to left directions. After leveling, turn front right (lock side)
leveling screw in about one-half turn to drop this corner
slightly to make the door easier to close and lock.
2. Voltage and Polarity Check . It is important that this
machine is hooked up to the proper voltage and polarity.
Using a voltmeter, perform the following checks from the
illustration shown.
(A)
(B)
(C)
(A) to (B) = 117 VAC (+-10%)
(A) to (C) = less than 1 VAC
(B) to (C) = 117 VAC (+-10%)
A. C. HOT (B)
A. C. NEUT (A)
EARTH (C)
GROUND
NOTE: Should the readings be different from above,
have a certified electrician correct the problem.
NOTE: Machines with refrigeration units delivered on
their sides should be stood upright for 24 hours
before the machine is plugged into an outlet.
IMPORTANT: A set of anchoring brackets are sent
with each machine. The kit is located in the bottom of
the machine complete with instructions. It is recom-
mended that this kit be installed to prevent shifting
of the machine. Part # 660438
◆
◆
◆
◆
◆
◆
◆
◆ ◆
◆
◆
◆
◆
◆
◆
◆
◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆
WATCH THROUGHOUT THE MANUAL FOR THIS
SPECIAL
◆
DIAMOND MARK.THIS INDICATES A
POINT OF SPECIAL INFORMATION OR A HINT
THAT WILL ASSIST YOU IN SETTING UP,
OPERATING OR TROUBLESHOOTING THE
MACHINE.
◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆
CAUTION: Certain procedures in both the operating section and the service section require that
voltage be on in the machine. Only trained personnel should perform this function. Exercise
extreme caution while performing these procedures. These procedures will be marked with the
lightening bolt symbol as it appears at left.
CAUTION: Certain procedures in both the operating section and the service section requires a
qualified trained technician to perform the particular task at hand.These procedures will be marked
with the exclamation symbol as it appears at left.
CAUTION: THIS MACHINE IS DESIGNED
FOR INDOOR USAGE ONLY. ANY OTHER
USAGE MAY VOID THE MANUFACTURERS
WARRANTY.
CAUTION: THE FOLLOWING PROCEDURE
REQUIRES THAT THE MACHINE HAVE
POWER APPLIED AND A POTENTIAL
ELECTRICAL SHOCK HAZARD EXISTS.