Automatic Products SNACKSHOP LCM5 Series, Instruction Manual

Page: 12 / 60

8
components
7. Vend Motors. The Snackshop LCM incorporates the use
of a high RPM DC motor. Due to new design, the vend
motor may no longer be homed by hand.
DO NOT TRY TO
TURN THE SPIRALS BY HAND. DAMAGE TO THE
MOTOR WILL RESULT.
It is also important to check
polarity before applying current to the motor. 2 diodes and
a capacitor are used to prevent circuit feedback and may
h ave to be checked when trouble shooting motor
problems.
8. Lighting System. There is only 1 flourescent lamp in the
Snackshop LCM.The lamp is located on the top, inside of
the door which lights up the main product area.The starter
is located on the hinge side of the lamp. The ballast and
line filter is located on the top, front, left shelf support.
(Page 18, Item 16.)
9. Main Product Shelves. There are three main product
shelves per machine. Each containing either 4 or 8
selections. Each selection has its own motor mounted to
the back of the shelf. Every shelf has its own harness and
plug for connecting to the remainder of the circuit through
the cabinet receptacle, located in the right, rear of the
cabinet.The motors are the same on either type shelf. It is
now possible in the Snackshop LCM to exchange a 4-
selection shelf with a 8-selection shelf or vice versa. You
also have the capability to gain 1/2" either up or down on
any shelf. To do this, the shelf should be removed and the
cabinet back harness receptacle lowered or raised with
the right and left shelf tracks.
Removing Product Shelf.
a. Lift up and push the lock levers towa r d
the back of cabinet. (Figure 1., Page 3.)
b. Pull shelf to its loading position.
c. Grasp shelf in front and rear center. Lift
front of shelf up above horizontal and pull shelf forward
while lifting.
d. To install shelf, reverse above procedure.
10. Delivery Bin. This is located below the display window on
the door and is mechanically operated.The linkage on the
outside end of the delivery bin may require occasionally
lubrication. Should the door become difficult to operate,
place a small amount of grease on the arm tracks.
Removing Delivery Bin.
a. Remove the screws from the underside
of the delivery bin.These screws fasten
into the lower door brace and remove
the screws and brackets at the top of
the delivery bin.
b. Grasp delivery bin on both sides, lift up and pull back.
Should bin be tight, rock it by lifting on one end, then
the other.
Figure 10.
NOTE: Use black color motor only.
NOTE:When exchanging the shelves, you will not
need any parts, but you will have to reprogram the
machines for prices and selections
the status of the selection. If the accumulated price and
the motor is present, a vend attempt will be made for
that selection. During this time, the selection will be
shown on the display. If credit is less than the selection
price, the price will be flashed for 3 seconds or until an
alpha key is pressed.If the motor is flagged as bad, the
selection and the “MAKE ALTERNATE SELECTION”
LED will be flashed for 3 seconds or until an alpha key
is pressed.
d. Change Payment. Following a successful vend, the
amount of change to be returned will be displayed for 2
seconds or until all coinage is paid back. A least coin
payout algorithm will be implemented.
e. Use Correct Change LED. If the changer’s least value
coin tube is empty, the “USE CORRECT CHANGE”
LED will be illuminated continuously.
6. Selection Panel. The selection panel
(Figure 10.)
on the
Snackshop LCM incorporates that use of a self enclosed
membrane switch panel.This eliminates the need for indi-
vidual switches and wiring.The membrane switch panel is
housed in a panel with individual buttons protecting the
switch face. The panel front also houses the display lens.
The display lens gives instructions to the customer for 2
conditions which might occur (make another
selection/use correct change).The display lens also con-
tains 3 LED lights.