9-20
FITTED EQUIPMENT
Cleaning
Clean the refrigerator thoroughly at intervals
as necessary. Turn off the gas, empty the
cabinet and defrost as described above. The
refrigerator and its accessories may then be
cleaned with a soft cloth wrung out in a weak
solution of bicarbonate of soda and warm
water. Finally, wipe over with a cloth rinsed in
warm water only and dry thoroughly. Do not
wash any plastic parts in water that is more
than hand hot and do not expose them to dry
heat.
NEVER USE STRONG CHEMICALS,
ABRASIVES, OR HIGHLY PERFUMED
CLEANING MATERIALS ON ANY PART OF
THE REFRIGERATOR.
Replace the accessories and re-light the
burner.
When Not in Use
Whenever your refrigerator is to be out of use
for a period, turn off the
gas or disconnect from the 12V supply, as
applicable. Empty the cabinet and defrost as
described earlier. Clean and thoroughly dry
the interior and accessories and
leave the
door open
otherwise the air inside may go
stale giving rise to an unpleasant odour
which could be difficult to remove at a later
date.
Consumption
The approximate gas consumptions at the
various settings of the gas control knob are
given below:
If the Refrigerator fails to work
Check the following points before calling a
service technician:
1.
That the “Starting the Refrigerator”
instructions habe been followed.
2.
The refrigerator is level and not tilted in
any direction.
3.
If it is possible to start the refrigerator on
any of the connected sources of energy.
GAS CONTROL SETTING
1
2
3
Bottled Gas lb liquid/24 hours
0.31
0.39
0.47
kg per 24 hours
0.13
0.17
0.2
4.
If the refrigerator fails to work on gas,
check.
•
That the gas bottle is not empty.
•
That all LP-gas valves are open.
5.
If the refrigerator fails to work on 12V,
check.
•
That the 12V supply is connected to
the refrigerator.
•
That the fuse on the 12V supply is
intact.
•
That the 12V switch is on.
6.
If the refrigerator fails to work on 230V,
check.
•
That the 230V supply is connected to
the refrigerator.
•
That the fuse is intact.
•
That the thermostat is not switched
to the ‘off’ position.
If the refrigerator is not cold enough it may be
because:
1.
The ventilation is inadequate owing to
objects such as wire mesh or winter
covers blocking the ventilation passages.
2.
The evaporator is frosted up.
3.
The temperature control setting is
incorrect.
4.
The gas pressure is incorrect - check the
pressure regulator at the gas container.
5.
The ambient temperature is too high.
6.
Too much food is loaded at the same
time.
7.
The door is not properly closed.
8.
More than one source of energy is used
at the same time.
If the refrigerator still does not work properly,
call a service engineer.
The sealed cooling system must not be
opened, since it contains corroding
chemicals under high pressure.
Summary of Contents for Topaz
