Auto Meter BVA-200s Operator'S Manual Download Page 11

14

11

After the Load Test is completed one of the following sample results will 

appear.

Ready for service.  

If the battery is marginal, it should 
be replaced under adverse driving 
conditions.   

Replace Battery 

Charge and place into service. 

Battery did not have a sufficient 

charge for a complete Load Test. 
Charge and retest. 

 

ALTERNATOR OVERVIEW 

This test measures the output of the alternator under load conditions.  
This information provides the basis for further charging system tests.  It 
also detects the presence of an open or shorted diode that causes an 
output loss of several amps and can cause the failure of other diodes.   

Symptomatic Check before Proceeding: 

  Battery should be in good condition and charged before testing the 

Alternator.

  Check warning light indications.  
  Check belt condition and tension.  
  Check all cables and connections.  
  Check the battery for corrosion and dirty terminals.  
  Does the battery have a low state of charge? (See section 2 and 3)
  Make sure all electrical items are off.  
  Check for Alternator noise.  

 

ALTERNATOR TEST 

Use the (+Up and -Down) keys 
to move cursor to the desired 
test. 

 

Start engine. 

Allow the voltage to stabilize 
until it stops rising.  Press 
(Y Enter) 

Note:

 Battery should be in good condition and charged before proceeding 

with this test. Press (N Esc.) to return to main menu.  Select 

Alternator 

Test

 then press (Y Enter).   

 BATTERY TEST 

 STARTER TEST 

>ALTERNATOR TEST 

 OTHER

>ALLOW VOLTAGE 

 TO STABILIZE 

 14.43V 

 ‘Y’ TO CONTINUE. 

START ENGINE.   

‘N’ TO CANCEL

#32 12V BATTERY

GOOD BATTERY.

12.84V CHG 100%

EST CCA   600

#33 12V BATTERY

BAD BATTERY

12.45V CHG 75%

EST  CCA   120

 

#34 12V BATTERY

GOOD NEEDS CHRG..

12.24V CHG 50%

EST  CCA   600

#35 12V BATTERY

CHARGE AND RETEST

12.06V CHG 25%

EST  CCA   320

#32 12V BATTERY

MARGINAL BATTERY.

12.84V CHG 100%

EST  CCA   600

Summary of Contents for BVA-200s













Reviews: