3
ENG
Please read this manual carefully before using the product to avoid
damage during use. Before switching on the product, make sure that
the technical specifications of the product shown on the label cor-
respond to the parameters of the electric network. Incorrect use can
lead to damage of the product, cause material damage or cause dam-
age to the health of the user. Use only for household purposes in ac-
cordance with this Manual. The product is not intended for commer-
cial use. Use the product only for its intended purpose. Do not use the
product outdoors and in rooms with high humidity. Always unplug
the product from the electrical network when it is not in use, as well as
before assembly, disassembly and cleaning. The product must not be
unattended while it is connected to the electric network. Make sure
that the power cord does not touch the sharp edges of furniture and
hot surfaces. To avoid electric shock, do not attempt to disassemble
or repair the product by yourself. When disconnecting the product
from the electric network, do not pull on the power cord, hold the
plug. Do not twist or wind the cord. The product is not designed to
be operated by an external timer or a separate remote control sys-
tem. The product is not intended for use by persons with reduced
physical, sensory or mental abilities, or if they have no experience
or knowledge, if they are not controlled or instructed about the use
of the device by the person responsible for their safety Do not allow
children to use the product as a toy. Do not use accessories that are
not included in the delivery suite.
ATTENTION!
Do not allow children
to play with plastic bags or wrapping film. THREAT OF SUFFOCATION!
ATTENTION!
Do not use this product outdoors.
ATTENTION!
Be es-
pecially careful if children under 8 years or people with disabilities
are close to the product in use.
ATTENTION!
Do not use this product
near combustible materials, explosives, or self-igniting gases. Do not
install this product near a gas or electric stove, or other heat sources.
Do not expose the product to direct sunlight.
ATTENTION!
Do not
allow children under 8 years to touch the body, the power cord and
the plug of the power cord while the product is in operation. If the
product has been kept for a while at a temperature below 0ºC, it must
be left at room temperature for at least 2 hours before switching it
on.
ATTENTION!
Do not handle the power cord and the power cord
plug with wet hands.
ATTENTION!
Unplug the product from the elec-
tric network every time before cleaning, and also if you do not use it.
When connecting the product to an electrical network do not use an
adapter.
ATTENTION!
To avoid overloading the electric network, do
not connect the product with other powerful electrical appliances to
the same electric network. Before filling or draining water from the
tank, and if you do not use the product, disconnect it from the electric
network. Place the iron on the ironing board carefully, so not to dam-
age the work surface.
ATTENTION!
Do not fill in the water tank with
flavoured fluids, vinegar, starch solution, descaling agents, chemicals,
etc.
ATTENTION!
The power cord plug has a wire and a grounding
prong. Only connect the product to a properly grounded socket.
AT-
TENTION!
Do not place the iron on metal or rough surfaces. Avoid
ironing on zippers, rivets, etc., as they can damage the working sur-
face.
ATTENTION!
Be careful and do not touch the metal parts of the
iron.
ATTENTION!
Regularly clean the iron from scum. Malfunctions
caused by the scum appearance on the component parts of the prod-
uct are not a guarantee event.
ATTENTION!
For additional protection
in the power circuit, it is advisable to install a residual current device
with a rated operating current not exceeding 30 mA. To install the de-
vice, contact a specialist.
SECURITY MEASURES
Plug the power cord of the iron into an socket. The indicator lights up.
Set the mechanical controller to the required temperature. When the
indicator turns off, you can start ironing. If you set the temperature less
than when you ironed, it is not recommended to start ironing until the
indicator lights up again.
IRON TEMPERATURE SETTING
Before work starts, refer to the instructions for ironing a particular type of
fabric. Select products for the fiber composition, depending on the tem-
perature of ironing: woolen to woolen, cotton to cotton, etc. Heating of
the iron is faster than cooling. So, start ironing the products that require
the lowest temperature, then go on to the next products. If the fabric con-
sists of different kinds of fibers, you need to start the ironing process from
the lowest required temperature. For example, fabric consists of 60% of
polyester and 40% of cotton you need to choose the temperature for
polyester. Turn the temperature controller to the position according to
the type of fabric that you are going to iron.
FILLING THE WATER TANK
Before filling the tank with water, unplug the product from the electric
network. Gently fill the tank with water. To prevent overflow, do not pour
water above the mark on the tank. If you want to add water during iron-
ing, first unplug the iron from the electric network.
SELECTING THE BODY POSITION
Iron holding your back straight. Set the height of the ironing board so
that the iron handle is on the same level with the elbow. If the tempera-
ture is correct, there is no need to press the iron hard. The best results are
achieved when the laundry is a little wet.
STEAMING
Turn the temperature controller to the position “••” or “•••” . Press the steam
button.
ATTENTION!
To prevent water dripping from steam holes, hold
the steam button for no more than 5 seconds.
SPRAYING
Spraying can be used at different temperatures and different operating
modes of the product if there is enough water in the tank. To use this
function, press the Spray button a few times.
STEAM FLOW
This function is used for additional single supply of the steam when
smoothening very crushed places. Set the thermostat to “••” or “•••” position,
press the steam button.
VERTICAL STEAMING
Make sure there is enough water in the tank. Connect the iron to the
electric network and place it vertically. Set the thermostat and the control
of the steam stripping to the maximum position. While holding the iron
vertically, press the steam button. The anti-leakage function automati-
cally prevents the formation of drops, allowing you to iron delicate fabrics
without risk of spoiling them or putting stains.
DRY IRONING
You can iron in dry mode, even if the tank is filled with water. However, with
prolonged operation in this mode, it is not recommended to pour into the
reservoir too much water. Set the steam control to the minimum position.
ANTI-CALC FUNCTION
The iron is equipped with the ANTI-CALC function to protect the iron
from scale formation.
ANTI-LEAKAGE FUNCTION „ANTI-DRIP“
The “anti-drip” function helps to avoid the water leakage and the forma
-
tion of divorces on the fabric, when the iron is operating at low tempera-
tures.
SELF-CLEANING
Fill the reservoir with water to the maximum mark, close the lid. Connect
the iron to the electric network. Use the thermostat to set the tempera-
ture to “MAX”. After the sole is heated, turn off the iron from the electric
network. While holding the iron horizontally above the sink, press the
“Self-clean” button. Steam and boiling water, going out from the nozzles,
will remove impurities. In this case, the iron should be shaken forward
and backward. If the iron becomes heavily soiled, repeat the self-cleaning
cycle. To dry the sole of the iron, iron a piece of unnecessary fabric.
END OF IRONING
Install the iron vertically. Set the controller to the “Min” position. Un
-
plug the iron from the electric network. Let it cool down. You can
wind the cord. Keep the iron in an upright position to avoid damage
of the working surface.
ATTENTION!
At the end of the work, it is always necessary to remove
water from the tank.
USE OF THE PRODUCT
Before cleaning the appliance, make sure that the iron is disconnected from the electric network and completely cooled down. Clean the
bodyt with a damp cloth, then wipe it dry. Do not use abrasive cleaners to clean the sole. Empty the water tank and then wind the power cord
around the iron base. To protect the working surface from damage, store the device in an upright position.
CLEANING AND MAINTENANCE
