background image

Rev. C 04/08 

01030 

 

TROUBLESHOOTING  

 

PROBLEM CAUSE 

CORRECTION 

Power base not running 

1. Power cord in not connected 
2. Switch in “OFF” position 

1. Connect power cord 
2. Rotate switch to “ON” position 

Fan not running 

1. Power cord in not connected 
2. Switch in “OFF” position 

1. Connect power cord 
2. Pull fan switch 

Unit not misting  

1. Water tank is empty 
2. Misting valve in ”CLOSED” position 
3. Water filter needs replaced 
 

1. Fill tank with DRINKING WATER 
2. Open valve (counterclockwise) 
3. Replace water filter 

Water streaming from nozzle 

1. Air filter needs replaced 
2. Air hose leaks  
 
3. Foreign object in nozzle 

1. Replace air filter 
2. Turn off fan motor, and feel any air 
leaks on hoses 
3. Order and replace nozzle holder 

Water dripping from drain plug 

1. Drain plug not seated 
2.Drain plug seal is missing or 
damage

 

 

1.Properly seat drain plug 
2.Replace drain plug seal

 

 

 
 
 

SAFETY

 WARRANTY

 

WARRANTY 

ONE YEAR FULL WARRANTY 

This product is warranted for one year from the date of purchase against defects in materials and workmanship.  At our 
discretion, parts that prove to be defective will either be repaired or replaced, or the whole product will be replaced.  In 
either case copy of your proof of purchase will be required. 
 
In case that any mechanical or electrical repairs are required during the warranty period send your complete product, 
postage or freight prepaid to the auraMIST service center near you.   Call the number below to get the nearest service 
center.   
 
This warranty does not include the air or water filters, which are expendable parts that can wear out from normal use 
within the warranty period.  This warranty applies for only 90 days if this product is ever used for commercial or rental 
purposes.   
 

AuraMIST, LLC  
5210 Village Parkway 
Rogers, AR 72758 

 
The model number and manufacturing date code can be found on the label attached to the back of the power unit. 
You should record both the model number and the date of purchase and keep in a safe place for future reference. 
 
MODEL NUMBER:   

XXXXX 

MFG DATE CODE:  

XXXX 

SERIAL NUMBER:   

XXXXXXX 

DATE OF PURCHASE: 

XX-XX-XX 

 
CUSTOMER SERVICE NUMBER: 

1-800-320-MIST 

Website: 

   www.auramist.net 

 

Summary of Contents for 1030









Reviews: