manualshive.com logo in svg

Audison bit Tune, User Manual

Share
Download
Audison bit Tune User Manual Download Page 92

USER’S MANUAL / bit Tune /

92

5.

 Select 

“Update Firmware”

 from the 

“SETTINGS”

 menu. The program will ask you to select the file you  

 

just saved from the Download area or previously saved to your PC.

6.

  Before starting the update of the bit Tune, the program provides the  

 

following warnings:

 

-

 Do not disconnect the 

bit Tune

 from the PC.

 

-

 Do not disconnect the 

bit Tune

 from power supply.

 

-

 Temporarily disable the automatic suspension processes on your PC.

 

-

 Temporarily disable the Screen Saver processes on your PC.

 

-

 Close any other open application.

 

-

 Temporarily disable anti-virus and anti-spy ware software.

7.

  Once the 

OK

 is given, start the 

Firmware

 update of the 

bit Tune

.  

 

This process takes from 30 seconds to 1 minute and its correct  

 

progress will be indicated by the time bar.

8.

  The successful update is indicated by the message window.

9.

  Turn the bit Tune off and on.

10

. Repeat the 

HSM

 microphone calibration 

(see sect. 7.2)

WARNING:

 

During the upgrade, the progress of the bar may stop for a few seconds.

 

 

Do not interrupt the process in any way.

9

Summary of Contents for bit Tune





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands