Audison bit Tune User Manual Download Page 9

Page: 9 / 100

USER’S MANUAL / bit Tune /

1. EMS COIL PICK-UP:

Input for inductive probe

(see sect. 8.4).

2. OPTICAL IN:

Optical S/PDIF Digital input stereo 192 kHz/24bit MAX.

3. PRE IN L R:

Measurement input with RCA connectors. Input sensitivity 70 V RMS max.

(see sect. 6.2.4.1, sect. 6.2.4.8)

These jacks are used for measuring pre-amplified signals.

4. BNC PROBE L R:

Measurement input with BNC connectors. Input sensitivity 70 V RMS max

(see sect. 6.2.4.1.

sect. 6.2.4.8)

and 700 V RMS activating the attenuator on probe X10. The

BNC PROBE L R

inputs are internally

protected by a T0.5A micro-fuse

(see section 9.3)

To connect to these inputs, use Probes provided inside the

product’s packaging:

5. SPEAKER IN L - R:

Measurement input with 4 mm banana sockets.

Input Sensitivity max 700 V RMS

(see sect. 6.2.4.1, sect. 6.2.4.8 )

. Use these jacks for level and power measurements.

The package includes terminated cables with 4 mm banana plugs with different types of termination:

6. SPEAKER LOAD SIMULATOR-SELECTOR:

Button for the selection of the simulated load on a OEM source.

Through the SPEAKER LOAD SIMULATOR LEDs

(see sect. 3.3.12-13)

you can check the need of the source to have

a load (speaker) in order to operate

(see sect. 8.1)

2 pairs; 4 mm Banana / 2 mm Banana

Red wire

Red

Black

Red

Black wire

White wire

Green wire

Red wire

Red

Black

Red

Black wire

White wire

Green wire

2 pairs, 4 mm Banana / Alligator

Red wire

Red

Black

Red

Black wire

White wire

Green wire

Red wire

Red

Black

Red

Black wire

White wire

Green wire

1 pair; 4 mm Banana / Measuring probe

Red wire

Red

Black

Red

Black wire

White wire

Green wire

Red wire

Red

Black

Red

Black wire

White wire

Green wire

2 pairs; 4 mm Banana / Spade connector

Red wire

Red

Black

Red

Black wire

White wire

Green wire

Red wire

Red

Black

Red

Black wire

White wire

Green wire

WARNING!

Do not use these jacks to:

Measure the outputs of bridge tied

amplifiers (btl).

Measure mains voltage (110 - 240 V) and

devices connected directly to the mains.

100 mm / 39.4 in.

70 mm / 27 in.

100 mm / 39.4 in.

3.2

REAR PANEL

Summary of Contents for bit Tune





































































































Search results

Summary of Contents for bit Tune

Reviews:

Brands by name

Popular brands

Audison bit Tune, User Manual

Search results

Summary of Contents for bit Tune

Reviews:

Brands by name

Popular brands