background image

  

 

27 

 

Discard the machine 

In accordance with the directive 2002/96/CE, the logo below indicates that the equipment concerned is 
not to be disposed of as ordinary waste at the end of its useable life. 
The equipment is to be delivered to a suitable depot that will dispose of the equipment in a proper way in 
accordance with the legislation on this subject, or to the supplier of new equipment in case of 
replacement. 
The owner of the equipment is responsible for proper disposal of the equipment. 
For further information we advise you to contact your local waste facility. 
 

 

Appropriate disposal of Waste of Electric and Electronic Equipment prevents unnecessary 
pollution of the environment and negative influence on general health. 

 
 

Conditions of guarantee 

 

9.1 

Liability 

1. 

We exclude any liability as far as it has not been arranged by law. 

2. 

Our liability will never exceed the amount of order. 

3. 

Subject to the general valid regulations of the law, we are not obliged to any compensation of 
damage of which kind ever, directly or indirectly, under which company damage, to movables and 
immovables or to persons, both to the opposite party as to third persons. 

4. 

In no way we are liable for damage arisen from or caused by the supplied or by the  

 

unsuitability of this for the purpose for which the opposite party has purchased the  

 

machine. 

 
 

9.2 

Guarantee 

1. 

With due observance of the restrictions stated hereafter, we allow 12 months of guarantee to the 
products supplied by us. This guarantee is restricted to the occurring manufacture errors and 
does not imply interruptions caused by any form of wear spare parts subject to use. 

2. 

To spare parts or enclosures obtained from third persons we do not give longer guarantee than 
this third supplier does. 

3. 

Guarantee expires if the opposite party and/or third parties associated make improper use of the 
supplied. 

4. 

Guarantee also expires if the opposite party and/or third parties associated execute activities 
and/or modifications to the supplied. 

5. 

In case we replace spare parts to fulfill our guarantee engagement, the spare parts replaced 
become property of AUDION ELEKTRO B.V. 

6. 

In case the opposite party does not come up completely, partially or does not come up in time to 
the obligations arisen from the closed engagement between the parties, we are not obliged to 
guarantee as long as the situation continues. 

 
 
 
 
 
 
 
 

Summary of Contents for LAMINO 301 LM































Reviews: