background image

2000 Series

 Installation and Operation

6

Transmitter Controls and Functions

Battery Selection

Two 1.5V AA alkaline batteries or rechargeable AA NiMH batteries 
for use with Audio-Technica’s ATW-CHG2 Recharging Station are 
recommended.  

UniPak

® 

Transmitter Battery Installation

1.  Open the transmitter door by pressing gently on the side-cover  
 

indentations and pulling back the hinged cover.

2.  Lift the battery-keeper arm, and carefully insert two fresh 1.5V AA  
 

alkaline batteries or rechargeable AA NiMH batteries, observing  

 

correct polarity as marked inside the battery compartment.

3.  Close the battery-keeper arm.

4.  Close the transmitter door.

Fig. E 

– UniPak

®

 Transmitter  Open

Handheld Transmitter Battery Installation

1.  While holding the upper part of the transmitter body below the ball- 
 

screen, unscrew the lower body cover, slide it downward, and  

 

remove it to expose the battery compartment.

2.  Observe correct polarity as marked inside the battery compartment  
 

and carefully insert two fresh 1.5V AA alkaline batteries or  

 

rechargeable AA NiMH batteries. Make certain the batteries are fully  

 

seated in the battery compartment. (

Fig. F

)

3.  Slide the lower body cover back up the body, then screw the  
 

housing together. Do not overtighten. 

Note: 

Remove batteries from the handheld transmitter starting at the 

bottom end, where finger indents in the battery housing are provided 
for easy grip.

Fig. F

 – Handheld Transmitter Battery Compartment

Battery Indicator  

After the battery is installed, turn on the power switch (located on 
the bottom of the handheld transmitter and on the top of the UniPak 
transmitter). The battery indicator LED (

Fig. G/H

) should turn red. If it 

does not, the batteries are installed incorrectly or they are dead.

Fig. G 

 – UniPak Transmitter  

Top View

  

UniPak

®

Transmitter Input Connection  

Connect an audio input device (microphone or guitar cable) to the 
audio input connector on the top of the transmitter. A number of 
Audio-Technica professional microphones and cables are available 
separately, pre-terminated with a UniPak input connector.

UniPak

®

 Transmitter Antenna

The ATW-T210a UHF UniPak

®

 body-pack transmitter includes one 

field-replaceable antenna mounted on the transmitter. The antenna 
simply screws into the transmitter’s antenna fitting. Check the installed 
antenna occasionally to make certain it is snugly attached (only finger-
tight). If the received signal is marginal, experiment with different 
transmitter positions on your body or instrument or try repositioning the 
receiver. 

Do not attempt to modify the transmitting antenna. Replace 

it only with the same parts,

 available from the Audio-Technica Service 

Department.

Charging Contacts

Transmitter 

 Door

Antenna

Audio Input Jack

Instrument/

Microphone Level Trim 

Controls

Channel Selector 

Switch

RF Power  

Select Switch

Service Port 

(for factory use only)

Battery-keeper 

Arm with 

Screwdriver 

attached

Power-on LED

Screwdriver

Input Connector

Power Switch

Battery Indicator

Antenna

Power Switch

Battery Indicator

Fig. H 

 – Handheld Transmitter 

Bottom View

Summary of Contents for 2000 Series













Reviews: