AuCom MVS0080 Product Manual Download Page 29

Page: 29 / 53

OPERATION: USER INTERFACE

710-03261-00D 28

MVS

Series

access is permitted. The security access code is requested once for the
programming session, and authorisation continues until the user closes the menu.

To enter the security access code, use the

◄

and

►

buttons to select a digit, and

the

▲

and

▼

buttons to change the value. When all four digits match your access

code, press <

STORE

> to submit the access code. The MVS Controller will display

an acknowledgement message before continuing.

Enter Access Code
1234

STORE

Access Allowed
Supervisor

8.4 LEDs

The MVS Controller has 13 LEDs for at-a-glance monitoring of starter status.

Starter status LEDs

Control input LEDs

Relay output LEDs

Start
Stop
Reset
Input A
Input B

Start
Run
Trip
Warning

Remote

RLA
RLB
RLC

S e r i e s

START

LCL/

RMT

LOGS

UNDO

STOP

RESET

SETUP

TOOLS

STORE

Starter

Status

Control

Inputs

Relay

Outputs

The Starter Status LEDs report the operating status of the soft starter:

•

The Start LED is on while the starter is starting, running or stopping.

•

The Run LED is on while the starter is running.

•

The Trip LED is on when a trip has occurred.

•

The Warning LED is on while a warning is active.

•

The Remote LED is on when remote mode is selected.

The Control Input LEDs activate when a signal is present at the corresponding
control terminals.

The Relay Output LEDs activate when the corresponding output relay is active.

8.5 Commissioning

Menu

The Commissioning Menu provides access to commissioning and testing tools.

To open the Commissioning Menu, press the <

SETUP TOOLS

> button while

viewing the metering screens.

Start
Stop
Reset
Input A
Input B

Start

Run
Trip
Warning
Remote

RLA
RLB
RLC

S e r i e s

START

LCL/

RMT

LOGS

UNDO

STOP

RESET

SETUP

TOOLS

STORE

Starter

Status

Control

Inputs

Relay

Outputs

RUNNING STOP IN 14:02
260a M1 88%

LCL/

RMT

STOP

RESET

SETUP

TOOLS

STORE

Setup Tools

button

Commissioning Menu

Reset Thermal Models

Parameter Archive

Run Simulation

Protection Simulation

Output Signal Simulation

Summary of Contents for MVS0080






















































Search results

Summary of Contents for MVS0080

Reviews:

Related manuals for MVS0080

Brands by name

Popular brands

AuCom MVS0080, Product Manual

Search results

Summary of Contents for MVS0080

Reviews:

Related manuals for MVS0080

Brands by name

Popular brands