background image

15/33 

 

Figure 18. How to enter a cooking profile.   

The example program in table 1 is used in this flow chart as a demo. 

 

 

4.1.2 Single-Step Mode

 

In single-step mode, you can only access and change the target cabinet temperature of 
Step 1 from the device. The controller will try to maintain the smoker temperature at the 
set temperature (Smkr Temp) of Step 1 continuously as long as the controller is powered 
on. If this controller is powered off and turned back on again, it will resume operating in 
this mode. You can still view and change settings in other steps in Cooking Profile on the 
AuberWIFI app (for WIFI model only), but they don’t apply to this mode. 
 
To change the set temperature in single-step mode, press the SET key once; it will show 
“Step: 1” and the current target cabinet temperature in the top line. A curser “>” will be 
shown  on the left  indicating which line will be selected.  Press  the  SET key  once.  The 
current  set  temperature  should  start  blinking.  Use 

  and 

  keys  to  change  the  set 

temperature. When finished, press the SET again to confirm the change. That number 
will stop blinking. Press the Timer/Back key to exit the menu. Or use 

  or 

  key to 

scroll  to  “Back”  and  then  press  SET  key  to  exit.  The  display  will  return  to  the  normal 
display mode if no key is

 

pressed in 15 seconds. 

00000000000000000000
00000000000000000000

>Step    1   SmkrTemp  250
   Back

00000000000000000000
00000000000000000000

Smkr    137            Food    122
Set       250      Probe3   270 

00000000000000000000
00000000000000000000

>Step    1   SmkrTemp  250
   Back

00000000000000000000
00000000000000000000

    Step    1   SmkrTemp  250
 > Back

SET

Press

SET

Press

Use 

 

or 

 

keys to adjust 

set pit temp. Press SET key 

to confirm.

Press

SET

 

 

 

 

Figure 19. How to change the set temperature in single-step mode. 

 

4.1.3 Program Status & Control 

(for firmware version 1.7.4 or newer)

 

Users can check or change current program running status by this parameter. It can be 
used to stop/start the program, or jump to a different step. This parameter is under the 
Cooking Profile menu as stated in section 4.1. Parameter name showing on the 
controller’s display is 

Prog Status. 

Available options for this parameter are: Stop, Start, 

Step 1 ~ 6, Back. 
 
When pressing the SET button momentarily to enter Cooking Profile menu, it will display 

Summary of Contents for AW-WST1510H-W


































Reviews: