manualshive.com logo in svg

Atmel Qmatrix, Application Note, Page: 26 / 27

Share
Download
Atmel Qmatrix Application Note Download Page 26

 

QTouch Schematic and Layout Checklist [APPLICATION NOTE]   

Atmel-42094C-QTouch-Schematic-and-Layout-Checklist-ApplicationNote_072014 

 

26 

5 

Revision History 

Doc Rev. 

Date 

Comments 

42094C 

07/2014 

1.  Changed to latest template. 
2.  Additional Schematic checklist items added under Atmel QTouch: 

•

 

Sense pin selection for Inter-Port / Intra-Port design 

•

 

Multiplexing sense line with programming line 

3.  Additional Schematic checklist items added under Atmel QMatrix: 

•

 

Using AIN1 pin for PWM generation 

•

 

Sharing YA/YB Ports 

•

 

Multiplexing sense line with programming line 

4.  Additional Schematic checklist items added under General section: 

•

 

Using multiple ground pins 

5.  Added below checklist items under General Layout section: 

•

 

Effects of conductive coating over front panel materials 

•

 

Effects of floating metal near touch sensors 

•

 

Proximity sensor design 

6.  Added References section. 
7.  Modified 

Figure 2-1

 and 

Figure 3-12

 for better understanding. 

42094B 

07/2013 

Section 

2.3 Atmel QMatrix

 updated: 

•

  Figure 2-3

. Y-line connection in Typical QMatrix Circuit updated 

•

 

Added tip to check list item “Rx/Ry = 1kΩ to 10kΩ”

 

42094A 

03/2013 

Initial document release. 

 

 

 

Summary of Contents for Qmatrix




























Reviews:

No comments