manualshive.com logo in svg

Atmel Qmatrix, Application Note, Page: 23 / 27

Share
Download
Atmel Qmatrix Application Note Download Page 23

 

QTouch Schematic and Layout Checklist [APPLICATION NOTE]   

Atmel-42094C-QTouch-Schematic-and-Layout-Checklist-ApplicationNote_072014 

 

23 

3.2.4  Sliders and Wheels 

•

 

There are no ground planes or foreign traces/components under the Slider/Wheel 

These can degrade the SNR and compromise the achievable resolution. This can manifest itself as jitter in the 

reported touch co-ordinate and is not desirable. 

 

•

 

Slider/Wheel has a segment size of 6mm to 8mm 

Segment size should be comparable to the diameter of a standard finger touch. Segments that are too large will 

lead to poor linearity. In case of Wheels the outer arc of the segment should be 6mm to 8mm long. 

 

•

 

In single layer Slider/Wheel, isolated X regions are connected using vias 

Since the Slider segments are on the same layer, the Y Electrode cuts through the X Electrode. This causes the 

X Electrodes to be split. These isolated regions need to be connected on the bottom layer using jumpers or vias. 

Figure 3-21.  Single Layer Slider/Wheel with X Electrodes Split by the Y Electrode 

 

 

•

 

In two layer Slider/Wheel the gap between Y Electrode traces is less than 4mm 

Gaps that are larger than 4mm can lead to an insensitive region on the Slider/Wheel. 

Figure 3-22.  Two Layer QMatrix Slider/Wheel 

 

 

 

Summary of Contents for Qmatrix




























Reviews:

No comments