manualshive.com logo in svg

Atmel Qmatrix, Application Note, Page: 15 / 27

Share
Download
Atmel Qmatrix Application Note Download Page 15

 

QTouch Schematic and Layout Checklist [APPLICATION NOTE]   

Atmel-42094C-QTouch-Schematic-and-Layout-Checklist-ApplicationNote_072014 

 

15 

•

 

Sense Lines are separated from all other tracks and components by at least T/2 

Sense Lines should not be placed near other tracks and components, as this may cause loading and 

interference. These will load the Sense Lines and reduce the sensitivity of the channel. Tracks with switching 

signals can cause noise in the Sense Lines if they are placed too close. 
 

•

 

There is no GND plane behind components, tracks and electrodes 

Keep solid Ground Plane or Fill away from the Sensor Signals. If shielding from noise sources is necessary a thin 

meshed ground may be used behind electrodes (<40% copper). Meshed ground can also be helpful in increasing 

SNR and stability when conducted noise is present. 

Figure 3-6. 

No Ground Flood Under Sense Components, Tracks, and Electrodes 

 

 

Figure 3-7. 

Meshed Ground to Provide Shielding from Noise Sources Behind the Board 

 

 

3.1.4  QTouch Slider or Wheel 

The checklist in this section is applicable only to QTouch designs. 

•

 

Small Slider/Wheel has a segment size of 6mm to 8mm 

Segment size should be comparable to the diameter of a standard finger touch. Segments that are too large will 

lead to poor linearity. In case of Wheel the outer arc of the segment should of length 6mm to 8mm. This is 

applicable to small spatially interpolated Slider/Wheel which uses simple rectangular or wedge shaped 

segments. 

 

Summary of Contents for Qmatrix




























Reviews:

No comments