manualshive.com logo in svg

Atmel Qmatrix, Application Note, Page: 13 / 27

Share
Download
Atmel Qmatrix Application Note Download Page 13

 

QTouch Schematic and Layout Checklist [APPLICATION NOTE]   

Atmel-42094C-QTouch-Schematic-and-Layout-Checklist-ApplicationNote_072014 

 

13 

•

 

Spacing between adjacent Sense Electrodes is at least T/2 

The separation between keys should be at least half of T (front panel thickness), to prevent cross-coupling and 

unintentionally touching a neighbouring key. The probability of an unintentional touch from the palm or 

hand-shadow should be minimal. 
 

•

 

LED holes have diameter less than 4mm 

LED holes that are too large can lead to poor sensitivity or cause the key to have a dead spot in the middle. 

Figure 3-2. 

Hole for Backlighting LED 

 

3.1.3  Routing 

•

 

Sense Lines are routed on the bottom layer 

Sense tracks are sensitive to touch and wherever possible they must be routed on the bottom layer to prevent 

false keys on the touch surface. 

 

•

 

Spacing between adjacent Sense Lines is at least T/2 

If Sense Lines are placed close to each other, it can cause cross-bleed and increase noise on the channels. It will 

also load both channels and decrease their sensitivity. 

Figure 3-3. 

Spacing Between Two Sense Lines 

 

 

 

Summary of Contents for Qmatrix




























Reviews:

No comments