AtlasIED LC372SR Installation Instructions And Use Download Page 10 | Manualshive

Page: 10 / 20

background image

PAGE

9

DOC: 1310B

REV: 10-12

LC372SR SOUND REINFORCEMENT MODULE

INSTALLATION INSTRUCTIONS

Optional LC372RMK Rack-Mount Installation Kit

The LC372RMK is available as an optional accessory used to allow mounting the LC372SR in a standard 19” equipment
rack. Attach the two rack ears as shown in Figure 8 using the mounting screws included with the kit.

Figure 8 -

LC372RMK Rack-Mount Installation

Optional LC372WMK Wall-Mount Installation Kit

The LC372WMK is available as an optional accessory used when installing the LC372SR on a wall or other flat surface.
Attach the two mounting plates to the bottom of the unit as shown in Figure 9 using the screws supplied with the kit.

Figure 9 -

LC372WMK Mounting Plate Installation

Attach the assembled unit to a wall or other suitable flat surface using screws that are suitable for the mounting surface.
Note that these screws are not included. Take care to ensure that sufficient space is left around the unit to allow air flow
through the ventilation openings and cool the unit.

«
...
8
9
10
11
12
...
»

Summary of Contents for LC372SR





















Reviews:

No comments

Related manuals for LC372SR

Brand: Taber Pages: 27

Brand: Rath Pages: 3

Brand: GE Pages: 24

Brand: Tacx Pages: 2

Brand: C.E. Nierhoff & Co Pages: 7

Brand: 4iiii Pages: 36

Brand: 4iiii Pages: 34

Brand: 4EVAC Pages: 27

Brand: Tascam Pages: 80

Brand: Tascam Pages: 2

Brand: Walker Pages: 24

Brand: B-K lighting Pages: 3

Brand: Banfer Pages: 6

Brand: Datalogic Pages: 48

Brand: PageFlip Pages: 32

Brand: EASTERN INSTRUMENTS Pages: 93

Brand: Pari Pages: 2

Brand: Gardner Bender Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands