manualshive.com logo in svg

Atlas XENOTEST BETA+, Operating Instructions Manual

Share
Download
Atlas XENOTEST BETA+ Operating Instructions Manual Download Page 46

46

Operating instructions  XENOTEST BETA+

7.

Operation

8. Enter the black standard temperature value read with the

XenoCal BST sensor into the input field. The display now
shows the old adjustment factor and the newly calculated
adjustment factor.
If the new factor is not within the tolerance (below 0.8 or
above 1.2), send the XENOSENSIV sensor in to ATLAS
for a check.

9. Confirm the new adjustment factor:

Press the 

b

key

After an adjustment has been made, the adjusted test parameters should be calibrated
(measured value check).

7.6

Control without senors

Controlling the irradiation intensity without XENOSENSIV sensor:

If the device is operated without the XENOSENSIV sensor, the control is perfomed in
accordance with the relative rating of the Xenon lamp within a range of 53 to 120 %.
100 % lamp rating correspond with the nominal rating of 2200 VA.
The control range of 100 to 120 % considers lamp aging.

NOTE - Operation without sensor

If the XENOTEST BETA+ is operated without
XENOSENSIV sensor, the adapter for opera-
tion without sensor (terminating plug) must be
connected to the connecting sleeve (see section
6.6).

Summary of Contents for XENOTEST BETA+





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands