Atlas Copco LP 13-30 P Original Instructions Manual Download

Page: 21 / 24

EC Declaration of Conformity

EC Declaration of Conformity (EC Directive 2006/42/EC)

We, Construction Tools EOOD, hereby declare that the machines listed below conform to the provisions of
EC Directive 2006/42/EC (Machinery Directive) and 2000/14/EC (Noise Directive), and the harmonised
standards mentioned below.

Guaranteed sound power level

[dB(A)]

Measured sound power level

[dB(A)]

LP 13-30 P

101

Following harmonised standards were applied:

◆

Following standards were applied:

◆

ISO 4413-ed3 2010-11-15

◆

BS EN 60204-1 2006 + A1 2009-04-30

◆

2014/30/EU

◆

73/23/EEC

Technical Documentation authorised representative:

Emil Alexandrov
Construction Tools EOOD
7000 Rousse
Bulgaria

General Manager:

Stijn Verherstraeten

Manufacturer:

Construction Tools EOOD
7000 Rousse
Bulgaria

Place and date:

Rousse, 2017-04-13

LP 13-30 P

Safety and operating instructions

Summary of Contents for LP 13-30 P

























Search results

Summary of Contents for LP 13-30 P

Reviews:

Related manuals for LP 13-30 P

Brands by name

Popular brands

Atlas Copco LP 13-30 P, Original Instructions Manual

Search results

Summary of Contents for LP 13-30 P

Reviews:

Related manuals for LP 13-30 P

Brands by name

Popular brands