ATH-Heinl ATH-Four Lift 55 Operating Instructions Manual Download Page 7

Page: 7 / 64

Manufacturer ATH-Heinl GmbH & CO.KG

- 7 -

Safety instructions

HAZARD INFORMATION
1.

The danger zone must be kept
clear when lifting and lowering

If there is a danger of the vehicle
falling, leave the danger zone

immediately

WARNING INFORMATION
3.

Lift may only be operated by

trained personnel.

Ensure there are no obstacles
when lowering

Prevent the lifted vehicle from
swaying significantly

Always ensure that the lifted
vehicle is secured so that it
cannot roll off.

Modifications of any kind to the
lift are not permitted

Leave the danger zone when
lowering the lift

Work on electrical components
may only be performed by locally
qualified electricians.

10.

Do not work on damaged lifts

11.

Only authorised persons are

allowed to enter the danger zone.

GUIDING PRINCIPLES

12.

Read and understand the
operating instructions before
operating the lift

13.

Do not clean the lift under
running water.

14.

Do not use any paint-dissolving or
strong, aggressive detergents

Summary of Contents for ATH-Four Lift 55




















































Search results

Summary of Contents for ATH-Four Lift 55

Reviews:

Related manuals for ATH-Four Lift 55

Brands by name

Popular brands

ATH-Heinl ATH-Four Lift 55, Operating Instructions Manual

Search results

Summary of Contents for ATH-Four Lift 55

Reviews:

Related manuals for ATH-Four Lift 55

Brands by name

Popular brands