ATH-Heinl ATH-Four Lift 55 Operating Instructions Manual Download Page 35 | Manualshive

Page: 35 / 64

background image

® Copyright ATH-Heinl GmbH & Co. KG, 2019, All rights reserved / Misprints and technical changes reserved / As of: 2019-01

Manufacturer ATH-Heinl GmbH & CO.KG

- 35 -

4.7

Disposal



Remove the air and power supply.



Remove all non-metallic substances and store them in accordance with local regulations.



Remove the oil from the machine and store it in accordance with local regulations.



Recycle all metallic substances.

The machine contains some substances that can pollute the environment and cause harm

to the human body if not handled correctly.

«
...
33
34
35
36
37
...
»

Summary of Contents for ATH-Four Lift 55

































































Reviews:

No comments

Related manuals for ATH-Four Lift 55

Brand: Laser Pages: 2

Brand: GSK Pages: 32

Brand: Sure Heat Pages: 10

BALBOA CS6000B Series

Brand: HydroQuip Pages: 32

Brand: H&S AUTOSHOT Pages: 23

Brand: SPT Pages: 32

Brand: M-system Pages: 3

Brand: Keithley Pages: 59

Brand: H2flow Pages: 16

Brand: Tews Technologies Pages: 22

Brand: Global Lift Pages: 51

Lumina LU20S-DNW

Brand: Leviton Pages: 3

Brand: WALTCO Pages: 44

Brand: Meilhaus Pages: 29

Brand: Viessmann Pages: 44

YUTAKI ATW-YMM-01

Brand: Hitachi Pages: 128

Relion 670 Series

Brand: Hitachi Pages: 192

Brand: HERKULES Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands