background image

Astria.US.com

126875-01_D

21

INSPECTING BURNERS

Check pilot flame pattern and burner flame patterns often.

PILOT FLAME PATTERN

Figure 33 shows a correct pilot flame pattern. Figure 34 shows an 

incorrect pilot flame pattern. The incorrect pilot flame is not touching 

the thermocouple. This will cause the thermocouple to cool. When 

the thermocouple cools, the heater will shut down.
If pilot flame pattern is incorrect, as shown in Figure 34.

•  turn heater off (see 

To Turn Off Gas to Appliance, page 19

•  see 

Troubleshooting, page 23

Note:

 The pilot flame on natural gas units will have a slight curve, but 

flame should be blue and have no yellow or orange color.

Figure 33 - Correct Pilot Flame Pattern (Your pilot may vary 

from pilots shown)

Pilot Burner

Thermocouple

Pilot Burner

Thermocouple

Figure 34 - Incorrect Pilot Flame Pattern (Your pilot may vary 

from pilots shown)

BURNER PRIMARY AIR HOLES

Air is drawn into the burner through the holes in the fitting at the 

burner entrance. These holes may become blocked with dust or lint. 

Periodically inspect these holes for any blockage and clean if needed. 

Blocked air holes will create soot.

MAIN BURNER

Periodically inspect all burner flame holes with the fireplace running. 

Some burner flame holes may become blocked by debris or rust, 

with no flame present. If so, turn off fireplace and let cool. Remove 

blockage. Blocked burner flame holes will create soot. 

BURNER FLAME PATTERN

 WARNING: If yellow tipping occurs, your fireplace 

could produce increased levels of carbon monoxide.

NOTICE: Do not mistake orange flames with yellow 

tipping. Dirt or other fine particles enter the fireplace 

and burn causing brief patches of orange flame. 

Burner flames will be steady, not lifting or floating—a bright yellow 

burner flame that will be blue next to the burner. Flame patterns will 

be different from unit to unit and will vary depending on installation 

type and weather conditions.  This can be dangerous. Inspect flames 

after installation to ensure proper installation and performance.
If burner flame pattern differs from that described:

•  turn fireplace off (see 

To Turn Off Gas to Appliance, page 19) 

•  see 

Troubleshooting, page 23

SPECIFICATIONS

ParisLights43ZMN

•  Rating (Variable): 25/39,000 Btu/Hr
•  Gas Type: Natural Gas
•  Ignition: Piezo
•  Pressure Manifold Setting: 3.5" W.C.
•  Inlet Gas Pressure (in. of water):

  Maximum - 10.5" W.C.
  Minimum* - 5.5" W.C.
* For purposes of input adjustment

ParisLights43ZMP

•  Rating (Variable): 29/37,000 Btu/Hr
•  Gas Type: Propane/LP Gas
•  Ignition: Piezo
•  Pressure Manifold Setting: 10.5" W.C.
•  Inlet Gas Pressure (in. of water):

  Maximum - 14" W.C.
  Minimum* - 11" W.C.
* For purposes of input adjustment

Summary of Contents for Paris Lights 43ZMN

































Reviews: