background image

General Information

900738-00  04/2017

Innovative Hearth Products
MHD35 Series Direct-Vent Gas Fireplaces

7

APPLIANCE OPERATION NOTICES

WARRANTY INFORMATION

IMPORTANT SAFETY AND WARNING INFORMATION

 CAUTION 

Hot while in operation. Do not touch. Severe Burns may result. Keep children, clothing 
furniture, gasoline and other liquids having fl ammable vapors away.

 ATTENTION 

L’appareil est chaud lorsqu’il fonctionne. Ne pas toucher l’appareil. Risque de brûlures 
graves. Surveiller les enfants. Garder les vêtements, les meubles, l’essence ou autres 
liquides produisant des vapeur infl ammables loin de l’appareil.

These fi replaces are vented gas appliances. Do not burn wood or other material in these 
appliances.

These appliances are designed to operate on natural gas or propane gas only. The use of 
other fuels or combinations of fuels will degrade the performance of this system and may be 
dangerous.

Provide adequate clearances around air openings and adequate accessibility clearance for 
service and proper operation. Never obstruct the front openings of the appliance.

These appliances are designed as supplemental heaters. Therefore, it is advisable to have an 
alternate primary heat source when installed in a dwelling.

Your gas appliance is covered by a limited 20-year warranty. You will fi nd a copy of the 
warranty accompanying this manual. Please read the warranty to be familiar with its 
coverage.

Retain this manual. File it with your other documents for future reference.

Failure to comply with the installation and operating instructions provided will result in an 
improperly installed and operating appliance, voiding its warranty.

Do not attempt to alter or modify the construction of the appliance or its components. Any 
modifi cation or alteration may void the warranty, certifi cation, and listings of this unit.

Summary of Contents for MHD35 Series









































































Reviews: