Aston Global Wamba, User Manual

Page: 17 / 36

30
• Select INSTALLATION (
쒀
and
쑽
) Press OK to confirm.
• Select ANTENNAS AND SATELLITES PARAMETERS (
쒀
and
쑽
). Press OK to confirm.
• Select TYPE OF INSTALLATION press CH+/CH- to choose MOTORIZED . Press OK to confirm and
go to the next step.
• Press CH+/CH- to choose the LNB type.
• Use (
쒀
and
쑽
) to select and access the following options and modify the corresponding parameters if
needed.
- POINTING
- SATELLITES ACTIVATION
- ADJUSTING LIMITS
- RESET AND CENTERING
- SAVE AND QUIT
ADJUSTING LIMITS
It is necessary and highly recommended to set the limits of your motor in order to avoid any deterioration of
your antenna and motor. Make sure that no physcal obstacles can interrupt the complete East/West rotation
of the antenna (+60/-60 degrees).
We strongly recommend, that your motorized system be installed by a qualified satellite engineer.
NB : If your motor does not require setting of limits or if the limits are already set, refer to chapter 4.2.2.
• Select ADJUSTING LIMITS (
쒀
and
쑽
) and then press OK to confirm.
• Select ON using
쑸
and
쑺
if you wish to activate the limits, and then press OK .
• Press OK to set the EAST LIMIT and then press the EAST key (red) until you reach the desired limit.
Press OK to confirm.
• Press OK to set the WEST LIMIT and then press the WEST key (blue) until you reach the desired limit.
Press OK to confirm.
• Press ESC to return to the previous menus and save the new parameters.
RESET AND CENTERING
WARNING !
Only a qualified satellite TV installation engineer can proceed with the following operations. Any misuse of
these functions may result in the damage of your motor.
The centering function allows you to set the motor on a new 0° satellite position or to go back to the factory
preset values.
• Move to RESET AND CENTERING using (
쒀
and
쑽
) and then press OK .
• Select CENTERING (
쒀
and
쑽
) if you want to adjust and set the motor to the 0° satellite position, then
press OK to confirm.
• Select AUTOMATIC RESET (
쒀
and
쑽
) if you want to adjust and set the motor to the 0° motor positionand
reprogram the usual satellites positions. Then press OK to confirm.
• Select MANUAL RESET (
쒀
and
쑽
) if you want to adjust your motor manually to the 0° motor position,
then press OK .
• Press EAST (red) / WEST (blue) keys, until you reach the desired position, then press OK to confirm the
new 0° motor position.
• Press ESC to save the modifications and go back to the previous menu.
31
POINTING
• Select POINTING (
쒀
and
쑽
) then press OK .
From now on the LocSat function is activated. It takes care of the automatic pointing of you’re antenna (if it
has a TracSat motor).
(1) A new menu will appear, you must select the desired satellite that will be considered as a reference
satellite to adjust your motor. Each of the following parameters can be modified if necessary, please refer
to chapter 4.1.
Satellite, Position, Frequency, Rate, Polarisation, PID video, PID audio, Location.
• Press CH+/CH- to select the desired satellite to be set as the reference,
• You can modify the different associated parameters, please refer to a recent specialist magazine giving
these parameters. Use (
쒀
and
쑽
) to move within the parameters and enter the new value.
• If your motor is an ASTON DH12 or DH23, select Automatic for the LOCATION by pressing CH+/CH-
and then OK to confirm. In this mode satellite localisation is fully automatic. In case of no success, check
all previous settings of the motor first, or use the Semi Auto mode.
• If your DiSEqC motor is not an ASTON , select Semi Auto mode and press OK to confirm. In this mode,
you need to manually locate the satellite. The motor will start moving in one direction. Wait until the motor
stops and use the
EAST and WEST keys to find the reference satellite.
• Once you have found the desired satellite, a signal appears on the level indicator and a channel on the
small
TV (if not scrambled). To find the optimum satellite direction, use EAST or WEST keys to adjust
your antenna. You can also use the Auto-Focus function by pressing the A/FOCUS key to do it
automatically.
(2) Press OK if you wish to choose another satellite and verify the new pointing position.
(3) Or press Esc to proceed.
From that moment, many operations are possible, RECALCULATING THE SATELLITES POSITIONS first
of all use SAVE A SATELLITE POSITION , if after recalculating positions the signal improves on a given
satellite when adjusting it and QUIT WITHOUT SAVING if you only want to check the aiming to a specific
satellite.
A - Recalculating all satellite positions
• If you are setting up the receiver for the first time, you need to RECALCULATE THE SATELLITE
POSITIONS just after the antenna dish adjustment (POINTING) . It will automatically recalculate all the
other satellite positions in accordance with the reference satellite you have just selected, adjusted and
validated its optimum direction.
• Select RECALCULATE SATELLITES POSITIONS (
쒀
and
쑽
) then press OK .
B - Save a satellite position
• When the positioning to a single satellite needs to be modified and saved separately without affecting the
other satellites in memory, then go to
SAVE CURRENT SATELLITE POSITION and press OK .
NB : All other satellite positions will not be modified.
C - Quit without saving
• When proceeding with a check adjustment on an already saved position, go to DO NOT SAVE SATELLITE
POSITION and press OK .
English