background image

INTRODUCTION                                                                                            

 

 

60089-05 

Page 1 

 

WARRANTY INFORMATION 

 
AST assumes that all persons operating or working on or with 
this system have read and understand the following operating 
instructions. 
 

  AST guarantees products of its manufacture, and bearing its 

name or logo and serial number identification, to be free 
from defects in workmanship or materials when used in 
accordance with AST instructions, properly maintained, and 
not misused. 

 

  AST’s obligation under this warranty is limited to repairing or 

replacing, at AST’s sole discretion, a defective AST product.  
AST assumes no liability for consequential or contingent 
damage of any kind.  AST assume no liability for lost work, 
business, revenue, profits, materials, or other claims of any 
kind. 

 

  This AST Warranty expires for each specific AST product 

after two-thousand (2,000) hours of normal usage, or three-
hundred-sixty-five (365) days, whichever first occurs, from 
the date of delivery to the first and original purchaser. 

 

  Any  claim  under  this  Warranty  must  be  filed  with  AST 

by  returning  the  subject  product  to AST,  transportation  
charges  prepaid,  within  fourteen  (14)  calendar  days 
from  the  date  of cause  of  claim  discovery,  or  from  the  
date  of  expiration,  whichever  first  occurs.    AST 
reserves  the  right  to  disclaim  any  Warranty  claim  that 
is  not  in  full  compliance  with  the conditions  and 
qualifications  for such claim under this Warranty 

 

  This AST Warranty  does not apply to any result of:  

normal  use and wear; misuse;  negligent use;  abrasion; 
corrosion;  accident;  improper  assembly  or  installation; 
product  rebuilding  by any party not authorized  by AST; or 
other product tampering. 

 

  A standard  commercial  component  used in or with an 

AST product,  but not manufactured  by AST, hereby is 
expressly excluded from this Warranty, and is covered 
under the original manufacturer's  warranty,  if any. 

 

  Damages  for breach of warranty  are limited to the 

purchase  price of the product. 

 

  AST  assumes  no  liability  for  consequential  or contingent 

damage  of any  kind,  including,  but not  limited   to:  loss  
of  business;   loss   of  production;   loss   of  reputation;  
loss  related   to defective   materials   or   workmanship;  
delay   in   manufacture,   repair   or   replacement;   or 
otherwise  related to an AST product. 

 

  AST  will  repair  or replace,  at normal  service  or  purchase 

charges,  a damaged  AST  product that  is  damaged  by  a 
cause  other  than  defective  materials  or  workmanship  
guaranteed under this Warranty. 

  AST  is not  responsible  for  labor  or material  charges 

arising  from  removal  or replacement  of parts guaranteed 
by this Warranty 

 

  This  Warranty is  expressly  in  lieu  of  any  and  all  other 

warranty,  guarantee,  obligation  or liability,  expressed  or 
implied.   Every  statutory  or implied  warranty,  including 
any warranty  of merchantability  or fitness for a purpose, 
hereby is expressly  disclaimed  and rejected. 

 

 

EVERY  SALE,  DELIVERY,  AND  TRANSFER  OF  TITLE 
AND  POSSESSION  OF  AN  AST PRODUCT   MUST  
AND   SHALL   BE   WITHIN   THE   UNITED   STATES  
OF   AMERICA. EVERY AST WARRANTY  OR 
GUARANTY  IS SUBJECT EXCLUSIVELY  TO THE 
JURISDICTION  AND LAWS OF THE STATE OF 
MINNESOTA,  U.S.A.

 

 

CUSTOMER SERVICE 

 

AST customer service & technical support is available Monday-
through Friday, 8AM – 4:30PM CST.  For more efficient 
service, have your machine’s serial number ready (serial 
number can be found on the front page of this instructional 
manual AND on a silver tag mounted on the machine). 

  REPLACEMENT/SPARE PARTS

 

o

  Online: 

www.ast-corp.net 

o

  Phone: 

763-592-2060 

o

  Fax: 

763-592-2075 

*Same day shipment on most parts 

Other services provided by AST include: 

 

TRAINING: Factory and field training seminars available 

 

INFORMATION: Complete service & maintenance history 
records for each current system, complete engineering & 
manufacturing specifications and drawings for all 
equipment, and complete inventory of consumable items 
are kept by AST. 

 

SUPPORT: AST provides engineering support to work with 
you in maintaining equipment and increasing production.  
AST also provides system upgrade support along with field 
upgrades, repair & service (both at the factory & in the field) 
and preventative maintenance programs. 

 

Summary of Contents for SOC GMP-050 Series
























Reviews: