Assa Abloy Sargent ELR Series Installation Instructions Manual Download Page 6

Copyright © 2020, Sargent Manufacturing Company

, an ASSA ABLOY Group company

. All rights reser

ved. 

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

05/31/20

A8239B • 800-810-WIRE (9473) • www.sargentlock.com

6

SE LP10 7000 Series Multi Point Lock

Wiring Diagrams

5

Product

8 PIN CONNECTOR

4 PIN CONNECTOR

1-Black

2-Red

3-White

4-Green

5-Orange

6-Blue

7-Brown

8-Yellow

1-Violet

2-Gray

3-Pink

4-Tan

ACCESS CONTROL DEVICES: SE LP10 7000 MP Lock, ElectroLynx  wire Color / Function assignments

12VDC

(Reader)

WIEGAND

WIEGAND

RX

RX

EGND

TAMPER

12/24 VDC

(LOCK RELAY)

DPS

DPS

GREEN_LED*

SARGENT -

SE LP10

7000 MP

NEG

POS

DATA_1

DATA_0

NO

 COM

EGND

OPEN 

COLLECTOR

NEG

POS

NC

COM

INPUT

Default Operation Mode:

•  Red LED ‘ON’ when powered.
•  Presenting a 13.56MHz or 125 kHz credential causes LED to briefly turn green and then return to 

red state.

•  Presenting a FIPS 201 PIV credential causes LED to turn amber as credential is authenticated. 

Reader emits a short beep when credential is successfully read. Reference Diagram #1.

PIN 4 (Tan –DPS COM )

PIN 2 (Gray – Lock POS)

PIN 1 (Violet – Lock NEG)

PIN 3 (Pink – DPS NC)

   Note: NC= Normally Closed 
             NO= Normally Open

PIN 8 (Yellow – TAMPER)
PIN 6 (Blue – RX COM)
PIN 4 (Green – Data 0)
PIN 2 (Red – Reader POS)

PIN 1 (Black – Reader NEG)

PIN 3 (White – Data 1)
PIN 5 (Orange – RX NO)

PIN 7 (Brown - EGND)

PIN 8 (Yellow – Green LED)

PIN 6 (Blue – RX COM)
PIN 4 (Green – Data 0)
PIN 2 (Red – Reader POS)

PIN 1 (Black – Reader NEG)

PIN 3 (White – Data 1)
PIN 5 (Orange – RX NO)

PIN 7 (Brown - EGND)

Optional Alternate Indicator Mode:

*Diagrams on following pages

Optional TAMPER Operation Mode:

•  Connect Yellow TAMPER wire from ElectroLynx cable to desired EAC panel control line.  

Reference Diagram #1.

•  As appropriate, use the configuration card to activate desired mode on reader.

•  Connect GREEN_LED input to switch controlled by panel. Shorting GREEN_LED to READER_NEG 

(Black) with panel switch will override reader LED to keep it green.

PIN 4 (Tan –DPS COM )

PIN 2 (Gray – Lock POS)

PIN 1 (Violet – Lock NEG)

PIN 3 (Pink – DPS NC)

Summary of Contents for Sargent ELR Series





















Reviews: