Assa Abloy Orion User Manual Download Page 49

Page: 49 / 55

ASSA ABLOY Hospitality

66 8003 015-3

Appendix A: Quick reference of technical data

Note:

If external motion sensor is applicable, see

Installation manual Orion High Voltage

Thermostat

for technical data and information about installation.

Dimensions (WxHxD)

112 x 117 x 35 mm (4 13/32" x 4 19/32" x 1 3/8")

Mains voltage input

Universal voltage input 100VAC-277VAC; 50/60Hz;
rated impulse voltage: 4kV

Switch input

Door switch - 1 exterior/1 interior

Multifunction input

Motion sensor/card switch/pipe temp sensor

High voltage outputs

(Fan 1): Type 1.B action. Max load 3A (3FLA/18LRA)

(Fan 2): Type 1.B action. Max load 3A (3FLA/18LRA)

(Fan 3): Type 1.B action. Max load 3A (3FLA/18LRA)

(reversing valve): Type 1 action. Max load 0.5A

Y (

cooling/compressor): Type 1 action. Max load 0.5A

(heating): Type 1 action. Max load 0.5A

Low voltage outputs

Proportional 0-10V; heating

Proportional 0-10V; cooling

Switch output

(max 24V AC/DC, SELV, max 0.1A)

Temperature sensor

Integrated in thermostat

Temperature display

Configurable:

room temperature

(default)

guest setting

Temperature display range

2-digit display

Adjustable setpoint
temperature range

17°C - 32°C / 62F - 90F

Environment

Normal indoor environment - Pollution degree 2
Operating temperature range 0°C - 55°C / 32F -130F

Temperature sensor

Integrated in thermostat

Service device

Orion Service

software and

service cable RJ12 to 3.5mm stereo jack

Radio (RF) signals

ZigBee 2006

Lock to thermostat:

Door open - staff card
Door open - guest card
Door open from inside
Door closed
Deadbolt thrown/released

Thermostat to lock:

Room occupied

Motion sensor to thermostat:

Motion detected
Battery status

Thermostat to motion sensor:

Turn off when the room is occupied and door is closed
Turn on when the door is opened again

Summary of Contents for Orion
























































Search results

Summary of Contents for Orion

Reviews:

Related manuals for Orion

Brands by name

Popular brands

Assa Abloy Orion, User Manual

Search results

Summary of Contents for Orion

Reviews:

Related manuals for Orion

Brands by name

Popular brands