ASROCK H77 Pro4-M Page 42 User Manual Download

Page: 42 / 71

2.17 Driver Installation Guide

To install the drivers to your system, please insert the support CD to your optical

drive fi rst. Then, the drivers compatible to your system can be auto-detected and

listed on the support CD driver page. Please follow the order from top to bottom to

install those required drivers. Therefore, the drivers you install can work properly.

2.18 Installing Windows

7 / 7 64-bit / Vista

/ Vista

64-bit With

RAID Functions

If you want to install Windows

7 / 7 64-bit / Vista

/ Vista

64-bit OS on your SATA

/ SATA2 / SATA3 HDDs with RAID functions, please follow the steps below.

RAID mode is not supported under Windows

XP / XP 64-bit.

STEP 1: Set up UEFI.

A. Enter UEFI SETUP UTILITY Advanced screen Storage Confi guration.

B. Set the option “SATA Mode Selection” to [RAID] for SATA2_2 to SATA2_5 and

SATA3_0 and SATA3_1 ports.

STEP 2: Use “RAID Installation Guide” to set RAID confi guration.

Before you start to confi gure the RAID function, you need to check the installation

guide in the Support CD for proper confi guration. Please refer to the document in

the Support CD, “Guide to SATA Hard Disks Installation and RAID Confi guration”,

which is located in the folder at the following path:

.. \ RAID Installation Guide

STEP 3: Install Windows

7 / 7 64-bit / Vista

/ Vista

64-bit OS on your

system.

After the installation of Windows

7 / 7 64-bit / Vista

/ Vista

64-bit OS, if you want to

manage RAID functions, you are allowed to use both “RAID Installation Guide” and “Intel

Rapid Storage Information” for RAID confi guration. Please refer to the document in the

Support CD, “Guide to SATA Hard Disks Installation and RAID Confi guration”, which is lo-

cated in the folder at the following path:

.. \ RAID Installation Guide

and the document in

the support CD, “Guide to Intel Rapid Storage”, which is located in the folder at the follow-

ing path:

.. \ Intel Rapid Storage Information

If you want to use “Intel Rapid Storage” in Windows

environment, install

“SATA2 driver” from the Support CD again so that “Intel Rapid Storage”

will be installed to your system as well.

Summary of Contents for H77 Pro4-M







































































Search results

Summary of Contents for H77 Pro4-M

Reviews:

Related manuals for H77 Pro4-M

Brands by name

Popular brands

ASROCK H77 Pro4-M, User Manual

Search results

Summary of Contents for H77 Pro4-M

Reviews:

Related manuals for H77 Pro4-M

Brands by name

Popular brands