ASM Polytouch HUDRASYNTH Deluxe Owner'S Manual Download Page 62

Page: 62 / 115

LFO parameters: page 2

Control knob

Parameter

Range

Description

Steps

2-64

Specific LFO points can be selected and defined

Smooth

0-127

Slows waveform changes

One-Shot

Off, On

On = LFO completes 1 cycle and stops

SemiLock

Off, On

Displays steps in semitone amounts inside the

Step Edit page

Step Edit..

(access)

Enters the Step Edit page

Three of those parameters are hidden for most LFO waveform selections, so we’ll describe the

other two first.

Smooth

Also known as “slew”, this parameter softens

the transitions from one amplitude of an

LFO to the next. When a waveform with

abrupt changes is selected (Saw, Square,

S&H, Step) the Smooth parameter makes the

LFO “glide” between adjacent values. At the

highest setting the square and triangle LFO

waveforms are identical.

One-Shot

An LFO will run its course only once if this

parameter is set to On. For example, it could:

• allow a single warble from a sine wave LFO
• introduce a short burst of chaos from the

Noise waveform

• run the Step LFO sequence one time, etc.

“Step LFO sequence?” Let’s discuss that feature

next.

The Step LFO

The Step LFO lets you define up to 64 stages

through which the LFO will pass. Its parameters

are only available when the LFO Wave selection

is set to Step. After that, three more parameters

appear on Page 2: Steps, SemiLock, and Step

Edit.
Those are described briefly in the previous

chart, and we’ll cover SemiLock more

thoroughly in the next section. Let’s walk

through an example with SemiLock Off for now.

1. Press [INIT] twice to initialize the patch
2. Hold [LFO 1] and press [OSC 1] to create

a mod route

3. Use Control knob 6 to set Depth to 128.0

4. Access [LFO 1]
5. Use Control knob 1 to select the Step

wave

6. Select page 2 with the Page down arrow
7. Notice that the Steps value is set to 8.

Leave it there for now.

8. Use Control button 8 to access the Step

Edit page

9. Notice that steps 1, 2, and 3 are set to

60.0, -60.0, and 0.0, respectively. Note:

Multiples of 5 provide specific pitches,

but intermediate values can be used

10. Hold a note. Three octaves of the same

pitch will play. The third pitch is longer

because the last six steps are set to the

same value.

11. Keep holding the note and notice that

the 8-step sequence repeats.

12. Enter values on the other steps to see

how that affects the Step LFO output.

Now that you know your way around the Step

LFO, let’s dive deeper.

SemiLock

SemiLock displays the steps inside the Step

Edit page in semitone values. This makes

it easy for an LFO to play standard 12-tone

pitches. Let’s try an example with SemiLock

On this time.

1. Press [INIT] twice to initialize the patch
2. Hold [LFO 1] and press [OSC 1] to create

a mod route

3. Use Control knob 6 to set Depth to 128.0

Summary of Contents for Polytouch HUDRASYNTH Deluxe




















































































































Search results

Summary of Contents for Polytouch HUDRASYNTH Deluxe

Reviews:

Related manuals for Polytouch HUDRASYNTH Deluxe

Brands by name

Popular brands

ASM Polytouch HUDRASYNTH Deluxe, Owner'S Manual

Search results

Summary of Contents for Polytouch HUDRASYNTH Deluxe

Reviews:

Related manuals for Polytouch HUDRASYNTH Deluxe

Brands by name

Popular brands