Component description
Components and measurement values
The specified resistance values apply at room temperature (about 20°C/68°F). Values within
±10% are considered normal.
Article no.
Component
Measurement value
Comment
80 839 15
Motor 50 Hz,
220/240 V
Winding resistance:
cable colour red-white 26.5
Ω
cable colour red-blue 53.5
Ω
cable colour white-blue 27.0
Ω
Current: 0.7 A; 140 W; 2850 rpm
80 839 16
Motor 60 Hz,
220/240 V
Winding resistance:
cable colour red-white 26.5
Ω
cable colour red-blue 53.5
Ω
cable colour white-blue 27.0
Ω
Current: 0.7 A; 140 W; 3300 rpm
The motor is a 2-pin motor and is directly
connected to the fan for internal air and the
gearing for driving the cylinder. On condenser
dryers, the motor also drives the fan for external
air.
80 903 13
Capacitor
8 μF
50 Hz
80 903 14
Capacitor
6 μF
60 Hz
80 902 70
Capacitor heat pump
17 μF
50 Hz
80 902 71
Capacitor heat pump
60 Hz
80 821 28
Condensate pump
50 Hz
80 846 48
Condensate pump
60 Hz
80 762 02
EMC-filter with inductor
The filter eliminates interference to and from the
machine.
80 833 44
Thermistor
4.8 k
Ω
(at 25°C)
The thermistor controls temperature regulation. If
the thermistor is short-circuited or detaches from
the control unit, the programme is stopped.
80 773 85
Thermostat 150
150°C automatic
The thermostat/overheating cut-out stops the
programme if the temperature becomes too high.
80 792 00
Thermostat 135
135°C automatic
80 902 24
Thermostat 110
110°C automatic
80 761 04
Door switch
The front door triggers a door switch which stops
the programme when the door is open. If the door
has been opened and closed during the programme
the machine must be restarted using the Start/Stop
button.
80 761 03
Microswitch float
Overflow guard
If both containers in the tumble dryer are full the
programme is stopped by a float switch installed
in the lower container. “Over flow” is indicated
on the display.
Electrical connection
Condenser
1950W/10A-2500W/16A
Vented
1950W/10A-3000W/16A
Heat pump
1300W/10A
Heating Water Circuit
1950W/10A
The machine is delivered as single phase and can
be switched between 10 A and 16 A. The control
buttons are used to make the switch via the software.
Does not apply to Heat Pump or Heating Water
Circuit.
80 824 92
Heating element 1950 W
Heater 1: 1950 W, 24.5
Ω
80 915 90
Heating element 2500 W
Heater 1: 1950 W, 24.5
Ω
Heater 2: 550 W, 91.4
Ω
80 824 91
Heating element 3000 W
Heater 1: 1950 W, 24.5
Ω
Heater 2: 1050 W, 45.5
Ω
80 824 60
Heating element 3000 W
Heater 1: 1950 W, 90.2
Ω
Heater 2: 1050 W, 167.6
Ω
Marine 440 V
80 824 61
Heating element 3000 W
Heater 1: 1950 W, 24,5
Ω
Heater 2: 1050 W, 45,5
Ω
3-Phase
80 916 18
Heating element 2500 W
Heater 1: 1950 W, 24,5
Ω
Heater 2: 550 W, 91,4
Ω
3-Phase
80 821 30
Cooling fan compressor heat
pump
637
Ω
80 821 22
Base heat pump complete
50 Hz
80 821 23
Base heat pump complete
60 Hz
80 88 415
Reversing valve
1.9 k
Ω
80 841 00
Steam generator
68
Ω
Thermistor 61.4 k
Ω
Steam pump 2.15 M
Ω
Supplied with steam pump
80 902 22
Reed switch steam tank
80 889 37
Control unit compl. TD70.C
The control unit contains microprocessors for
controlling programmes, the motor, the heating
elements etc.
80 846 49
LED-light compl.
LED-technology for the machine’s internal light.
Service Manual TD70.C
9
