background image

Ascon Tecnologic - K48 Line - ENGINEERING MANUAL -Vr. 09 - 

PAG. 1

K48

CONTROLLER AND  

MINI-PROGRAMMER

Engineering Manual

Code : ISTR-MK48-ENG09 - Vr. 09 (ENG)

Ascon Tecnologic S.r.l.

Viale Indipendenza 56, 27029 Vigevano (PV) - ITALY

Tel.:

 +39 0381 69871/

FAX:

 +39 0381 698730

www.ascontecnologic.com

e-mail:

 

[email protected]

1.  OuTLINE DIMENSIONS (mm)

1.1  Dimensions

K48

48

48

98

48

44.5

9.5

283.5.

Tun

Out1 Out2

Prg

Out3

45

45

Panel + Gasket max. 9 mm

Bracket type 1

Bracket type 2

1.2  Mounting requirements

This instrument is intended for permanent installation, for 
indoor use only, in an electrical panel which encloses the 
rear housing, exposed terminals and wiring on the back.
Select a mounting location having the following characteristics:

1. 

It should be easily accessible;

2. 

There are minimum vibrations and no impact;

3. 

There are no corrosive gases;

4. 

There are no water or other fluids (i.e. condensation);

5. 

The ambient temperature is in accordance with the 
operative temperature (0... 50°C);

6. 

The relative humidity is in accordance with the instrument 
specifications (20... 85%);

The instrument can be mounted on panel with a maximum 
thickness of 15 mm. 
When the maximum front protection (IP65) is desired, the 
optional gasket must be monted.

2.  CONNECTION DIAGRAM

OUT1

OUT2

OUT3

Power

supply

Out1, Out2: Relay 8A-AC1 (3A-AC3)/250VAC

Out3: Relay 5A-AC1 (2A-AC3)/250VAC

SSR: 8mA/8VDC

TC/mV

Pt100

4... 20 mA active

PTC-NTC

Out 12 VDC max. 20 mA

Ext.

gen.

0/4...20 mA active
0... 50/60 mV;  0... 1 V;  0/1... 5 V; 0/2... 10 V

INPUT

4... 20 mA passive (2 wires)

DI1
DI2

2.1  General notes about wiring

1. 

Do not run input wires together with power cables.

2. 

External components (like zener barriers, etc.) connected 
between sensor and input terminals may cause errors in 
measurement due to excessive and/or not balanced line 
resistance or possible leakage currents.

3. 

When a shielded cable is used, the shield should be 
connected to ground at one point only.

4. 

Pay attention to the line resistance; a high line resistance 
may cause measurement errors.

Summary of Contents for K48





































Reviews: