Ascon tecnologic DY-5121 User Manual Download Page 8 | Manualshive

Page: 8 / 50

background image

delta

due DY-5121 - User manual

2

1-2

Mounting

A - Sanp ON

B - Snap OFF

1. Snap the device on the DIN-rail (as described in picture A above).

2. Connect the Ethernet cable to the RJ45 connector.

3. Connect the ModbusRTU network to the DSUB connector (RS-232) or the

6-pole RJ12 connector (RS-485).

4. Connect the Power Supply and apply power.

5. Now you can start using the Protocol converter. Use the “

DY-5xx1 Config

Utility” to configure the IP address and other network settings.
See 2-1 - Configuring the Protocol Converter for further information.

Note:

The default IP address of the webSCADA Protocol converter is 10.200.1.1.
Please change this IP-address to a valid address in your network.
Also, make sure not to power up more than one network attached Protocol
converter before IP-address is changed or DHCP enabled.

«
...
6
7
8
9
10
...
»

Summary of Contents for DY-5121



















































Reviews:

No comments

Related manuals for DY-5121

Brand: S.M.S.L Pages: 16

Brand: Allen-Bradley Pages: 4

Brand: Patton electronics Pages: 11

Parallel Port Input/Output Converter PPIO

Brand: B&B Electronics Pages: 34

Brand: WATANABE Pages: 2

Brand: Humandata Pages: 10

Brand: Love Controls Pages: 2

Brand: FONESTAR Pages: 9

10/100/1000 (SFP)

Brand: Dynamix Pages: 2

Brand: Cablematic Pages: 3

Brand: e+p Pages: 2

Brand: Transition Networks Pages: 7

Brand: ADF Web Pages: 29

E70ACMS4 Series

Brand: Lenze Pages: 20

Brand: Partilink Pages: 30

Brand: AUTLED Pages: 2

Brand: MPP Solar Pages: 33

Brand: GREISINGER Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands