manualshive.com logo in svg

Asante GigaNIX 1000T, User Manual

Share
Download
Asante GigaNIX 1000T User Manual Download Page 26

GigaNIX Windows NT/2000 Driver Installation

22

Version 2.0

GigaNIX 1000T User Manual

GigaNIX Installation on a Windows NT/2000 platform
This section describes the installation of the GigaNIX in Windows NT environment.

For specific details on performing the hardware installation, please refer to the
system’s user manual.

Windows NT Pre-Installation Checklist
Check to see that your server meets Hardware and Software requirements listed in
the Windows NT System Requirements table below:

Verify that your system is using the latest BIOS.  Review the information in the
ReadMe file on the CD-ROM for more information not available at the time this

manual was written. If your system is active, shut it down

When the system shut down is complete, power off and unplug your system

Category

Requirements

Hardware:

Pentium based computer that
meets Window NT 4.0 software
requirements
One open 32/64 bit PCI slot
128 MB DRAM (Min.)

Software:
Operating System

Microsoft Windows NT 4.0 (server

or workstation) with Service Pack 4
or later
Microsoft Windows 2000

WINDOWS NT SYSTEM REQUIREMENTS TABLE

Summary of Contents for GigaNIX 1000T


































Reviews:

No comments

Brands by name

Popular brands

Load more brands